参数资料
| 型号： | 3/4-5-4991 |
| 厂商： | 3M (TC) |
| 文件页数： | 9/11页 |
| 文件大小： | 0K |
| 描述： | TAPE VHB ACRYLIC FOAM 3/4" X 5YD |
| 视频文件： | 3M VHB adhesive demonstration - Another Geek Moment |
| MSDS 材料安全数据表： | 49zz MSDS |
| 标准包装： | 1 |
| 系列： | VHB™ 4991 |
| 胶带类型： | 双涂层，双面 |
| 胶合剂： | 丙烯酸 |
| 背衬，载体： | 聚乙烯薄膜 |
| 厚度： | 0.090"（90 mils，2.286mm） |
| 厚度 - 胶合剂： | 0.085"（85 mils，2.159mm） |
| 厚度 - 背胶，载体，衬垫： | 0.0050"（5.0 mils，0.127mm） |
| 宽： | 0.75"（19.05mm）3/4" |
| 长度： | 15'（4.6m）5 码 |
| 颜色： | 灰 |
| 使用： | 通用 |
| 温度范围： | 200°F（93°C） |
| 包装： | 散装 |
| 其它名称： | 3M9852 |
3M ? VHB ? Tapes
Application Techniques
Clean: Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA*) and
water prior to applying 3M? VHB? Tapes.
Exceptions to the general procedure that may require additional surface preparation include:
? Heavy Oils: A degreaser or solvent-based cleaner may be required to remove heavy oil or grease from a
surface and should be followed by cleaning with IPA/water.
? Abrasion: Abrading a surface, followed by cleaning with IPA/water, can remove heavy dirt or oxidation
and can increase surface area to improve adhesion.
? Adhesion Promoters: Priming a surface can significantly improve initial and ultimate adhesion to many
materials such as plastics and paints.
? Porous surfaces: Most porous and fibered materials such as wood, particleboard, concrete, etc. need to be
sealed to provide a unified surface.
? Unique Materials: Special surface preparation may be needed for glass and glass-like materials, copper
and copper containing metals, and plastics or rubber that contain components that migrate (e.g. plasticizers).
Refer to 3M Technical Bulletin “Surface Preparation for 3M? VHB? Tape Applications” for additional
details and suggestions. (70-0704-8701-5)
*Note: These cleaner solutions contain greater than 250 g/l of volatile organic compounds (VOC). Please
consult your local Air Quality Regulations to be sure the cleaner is compliant. When using solvents,
be sure to follow the manufacturer ’s precautions and directions for use when handling such materials.
Pressure: Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm
application pressure develops better adhesive contact and helps improve bond strength. Typically, good surface
contact can be attained by applying enough pressure to insure that the tape experiences approximately 15 psi
(100 kPa) pressure. Either roller or platen pressure can be used. Note that rigid surfaces may require 2 or 3 times
that much pressure to make the tape experience 15 psi.
Temperature: Ideal application temperature range is 70°F to 100°F (21°C to 38°C). Pressure sensitive
adhesives use viscous flow to achieve substrate contact area. Minimum suggested application temperatures:
? 50°F (10°C): 3M? VHB? Tapes 4950, 5952, 4910, 4952, 4611, 4622 families.
? 60°F (15°C): 3M? VHB? Tapes 4941, 4945 families.
? 32°F (0°C): 3M? VHB? Tape 4951 families.
Note: Initial tape application to surfaces at temperatures below these suggested minimums is not
recommended because the adhesive becomes too firm to adhere readily. However, once properly
applied, low temperature holding is generally satisfactory.
To obtain good performance with all 3M? VHB? Tapes, it is important to ensure that the surfaces are dry
and free of condensed moisture.
Time: After application, the bond strength will increase as
Bond Typical Build vs. Time
●
★
★
●
●
the adhesive flows onto the surface (also referred to as “wet out”).
At room temperature approximately 50% of ultimate bond
strength will be achieved after 20 minutes, 90% after 24 hours
and 100% after 72 hours. This flow is faster at higher temperatures
and slower at lower temperatures. Ultimate bond strength can be
achieved more quickly (and in some cases bond strength can be
increased) by exposure of the bond to elevated temperatures
60
20
PERCENT OF FULL BOND
100 ■ ■ ■
■ ●
●
80 ■ ●
●
●
★
40 ★
★
■
●
★
■
●
★
■
●
■
★
■
★
■
★
●
■ ●
★
●
★
●
★
(e.g. 150°F [66°C] for 1 hour). This can provide better adhesive
wetout onto the substrates. Abrasion of the surfaces or the use of
0
20 MIN
1 HOUR 24 HOURS
● ROOM TEMP ★ 50°F
■ 150°F or ABRADE
72 HOURS
primers/ adhesion promoters can also have the effect of increasing
bond strength and achieving ultimate bond strength more quickly.
-9-
相关PDF资料 |
PDF描述 |
|---|---|
| TXS2-L-12V | RELAY GEN PURPOSE DPDT 1A 12V |
| 0395326512 | 5.08MM EURO HEADER RA GRN 12POS |
| SSRC-480D5 | RELAY SSR 480VAC 5A SIP AC OUT |
| 0395320014 | 5.08MM EURO HEADER RA BLK 14POS |
| SSRC-240D5R | RELAY SSR 240VAC 5A SIP AC OUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 3454LS2027B | 制造商:Amphenol Corporation 功能描述:CONN MIL-C-5015 CIRC SKT 14 POS CRMP ST JAM NUT 14TERM - Bulk |
| 3454W22-14PW | 制造商:undefined 功能描述: |
| 3455 | 功能描述:电缆固定件和配件 .25" - .49" CABLE PG HUB GRAY RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 3455 00210349 | 功能描述:恒温器 COMMERCIAL THERMAL RoHS:否 制造商:Maxim Integrated 功能: 开路温度: 闭合温度: 准确性:+/- 1 C 温度范围:- 55 C to + 125 C 电流额定值:500 uA 电压额定值:2.7 V to 5.5 V 产品:Thermostats |
| 3455 00560044 | 功能描述:恒温器 COMMERCIAL THERMAL RoHS:否 制造商:Maxim Integrated 功能: 开路温度: 闭合温度: 准确性:+/- 1 C 温度范围:- 55 C to + 125 C 电流额定值:500 uA 电压额定值:2.7 V to 5.5 V 产品:Thermostats |
发布紧急采购，3分钟左右您将得到回复。