- 您现在的位置：买卖IC网 > PDF目录20537 > 3021HEP (LEDdynamics Inc)LED SUPPLY CONST CURR BUCKPUCK PDF资料下载
参数资料
| 型号： | 3021HEP |
| 厂商： | LEDdynamics Inc |
| 文件页数： | 4/8页 |
| 文件大小： | 0K |
| 描述： | LED SUPPLY CONST CURR BUCKPUCK |
| 标准包装： | 25 |
| 系列： | BuckPuck™ 3021/3023 |
| 附件类型： | 线束 |
| 适用于相关产品： | BuckPuck™ 3021/3023 LED Supply |
| 其它名称： | 788-1092 |
3021/3023 BuckPuck
TM
Wide Range LED Power Module
DATA SHEET Page 4 of 8
Adjustable Current - On-Board Control - “I” Model
Where the ability to adjust the output current to an intermediate value is required, all output current ratings are
available with an on-board potentiometer. This permits the output current to be varied from approximately 40%
to 110% of the rated value. When measuring the output is required to determine a particular set point, the
following method is recommended:
Temporarily place a 0.1 ohm, 1% resistor in series with the LEDs.
Read the voltage across the 0.1 ohm resistor.
The voltage, in millivolts X 10, will equal the output current in mA.
Because there is a small, high-frequency component in the 3021/3023 output, many multi-meters may give an
incorrect reading when used in the current mode. It has been found that the method described above yields a far
more accurate measurement.
The potentiometers used for the on-board adjustable units are rated for a limited number of rotations (typically
100) and are intended for "set it and forget it" applications. Where frequent adjustments of output current are
needed, the use of units with external adjustment capabilities is recommended.
Adjustable Current - External Control - “E” Model
Figures 10 and 11 show external adjustment con gurations. Both use a 5Kohm, linear taper potentiometer. In
Figure 10, the potentiometer is connected between the internal 5V DC reference (Ref) output and the control (Ctrl)
input. When using this con guration, it is important that Vin be 7V DC or higher. Figure 11 shows the control
potentiometer being powered by an external 5V DC source. When using an external power source for the
potentiometer, the source ground must be common to the LED- output pin. In either con guration, connect the
potentiometer such that clockwise rotation increases the resistance. Note that, because the current through the
potentiometer is less than 5mA, a low power potentiometer may be used.
External On/O Control
Where a manual on/o control is desired, the potentiometer in Figures 10 and 11 may be replaced by a pushbutton
or toggle switch. The output current will be zero when the switch is closed. Figures 12 and 13 show external
dimming control combined with on/o control. The circuit in Figure 13 uses a 2N3906 or equivalent PNP
switching transistor.
External Pulse/Strobe Control
Figures 14 and 15 show two methods for low speed pulsing or high speed ashing operation. In Figure 14, a
5V TTL/CMOS logic signal is applied directly to the control (Ctrl) input of the 3021/3023. The output current will be
zero when the control signal is high. Note that the input needs to source a minimum of 4.75V DC into a 1.5Kohm
input impedance. Also, as is the case with a dc control signal, the logic input ground should to be common to the
LED- output terminal.
Figure 15 shows an inverted input con guration using a 2N3906 or other PNP switching transistor. In this case, a
logic high will cause the output to be "on". In either con guration, the rise time of the output will be 10μsec or
less. A pulse frequency up to 10kHz may be used.
LEDdynamics, Inc.
802.728.4533 P
802.728.3800 F
sales@LUXdrive.com
www.LUXdrive.com
Made in
?2013 LUXdrive, A Division of LEDdynamics, Inc. www.LUXdrive.com.
Speci cations subject to change without notice. May, 2013 - Rev 3.1
the USA
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17604AUA+ | IC MOSFET DRVR 4A DUAL 8UMAX |
| SBR20A300CT | DIODE SBR 20A 300V TO220-3 |
| LQM2HPN1R5MG0L | INDUCTOR 1.5UH 20% 1500MA 1008 |
| MAX17603AUA+ | IC MOSFET DRVR 4A DUAL 8UMAX |
| LM385BM-2.5/NOPB | IC VREF SHUNT 2.5V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 3021HN | 功能描述:LED SUPPLY CONST CURR BUCKPUCK RoHS:是 类别:电源 - 外部/内部（非板载） >> 配件 系列:BuckPuck™ 3021/3023 标准包装:1 系列:VS/MP 附件类型:连接器套件 适用于相关产品:- |
| 302-1K | 功能描述:厚膜电阻器 - SMD USE 302-1.0K-RC RoHS:否 制造商:Bourns 电阻:1.5 Ohms 容差:1 % 功率额定值:25 W 电压额定值:250 V 外壳代码 - in: 外壳代码 - mm: 端接类型:SMD/SMT 温度系数:100 PPM / C 系列:PWR163 工作温度范围:- 55 C to + 155 C 封装:Tube |
| 3021-KS | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 3021R-A-.045-22 | 制造商:Accurate Screw Machine 功能描述: |
| 3021R-A-.156-1 | 制造商:MISCELLANEOUS 功能描述: |
发布紧急采购，3分钟左右您将得到回复。