- 您现在的位置：买卖IC网 > Datasheet目录596 > 318837-1 (TE Connectivity)EXTRACTION TOOL .093 CONN Datasheet资料下载
参数资料
| 型号： | 318837-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/1页 |
| 文件大小： | 0K |
| 描述： | EXTRACTION TOOL .093 CONN |
| 标准包装： | 1 |
| 工具类型： | 拔出工具 |
| 适用于相关产品： | 矩形连接器触点 |
| 产品目录页面： | 241 (CN2011-ZH PDF) |
| 配用： | A100558CT-ND - CONN SOCKET 24-18AWG TIN .093" A100560CT-ND - CONN CONTACT PIN 24-18AWG TIN A100559CT-ND - CONN SOCKET 24-18AWG GOLD .093" 770144-6-ND - CONN SOCKET 20-14AWG CRIMP TIN 350418-5-ND - CONN CONTACT PIN 24-18AWG GOLD A100559TR-ND - CONN SOCKET 24-18AWG GOLD .093" A25780CT-ND - CONN SOCKET 14-18AWG TIN CRIMP A25512CT-ND - CONN PIN 14-18AWG .093 TIN A25511CT-ND - CONN SOCKET 14-20AWG .093 TIN A25510CT-ND - CONN PIN 14-20AWG .093 TIN 更多... |
| 其它名称： | A9950 |
Extraction Tool 318837- 1
Instruction Sheet
408-- 4375
21 APR 11 Rev A
Plastic
Handle
Interlock
Lever
Figure 1
Spring-- Loaded
Metal Tip
NOTE If pushing the wire by hand is difficult, use
Insertion Tool 91002--1.
i
3. Depress the extraction tool interlock lever and
insert the tip of the tool into the contact cavity in
the mating face of the housing. Make sure that the
tip is completely bottomed in the cavity.
Push Wire Toward
Housing Before
Engaging Tool Tip
Interlock Lever
Depressed
1. INTRODUCTION
i
Extraction Tool 318837--1, shown in Figure 1, is
designed to remove the .093 Commercial Pin and
Socket contacts listed in Figure 2 from connector
housings. Read these instructions thoroughly before
attempting to remove any contacts.
.093 COMMERCIAL PIN AND SOCKET
CONTACT BASE PART NUMBER
STRIP-- FORM LOOSE-- PIECE
350415 770144
350416 770145
350417 770146
350418 770147
770383
770385
770529
770530
770815
Figure 2
2. DESCRIPTION (Figure 1)
The extraction tool consists of a spring--loaded metal
tip with an integral plunger mounted to a plastic
handle with an interlock lever. When the interlock
lever is depressed, the plunger is held until the
contact locking lances are depressed by the tip. After
the lever is released, the plunger is released,
permitting the contact to be pushed out the rear of the
housing.
3. EXTRACTION PROCEDURE (Figure 3)
1. Determine the contact to be removed and grasp
the wire attached to that contact.
2. Move the contact forward as far as possible by
pushing the wire toward the housing.
Mating Face of
Housing (Ref)
Figure 3
4. While holding the extraction tool in position and
pulling back on the wire, release the interlock lever
and push the tool handle forward. The wire and
contact should pull out of the housing.
NOTE Before using the contact again, reset the locking
lances to their original positions. To obtain the
correct setting dimensions for the locking lances,
consult the Customer Drawing covering the
specific contact, or contact TE Connectivity
Engineering.
4. TOOL MAINTENANCE
It is recommended that the tool be inspected when
you receive it and at regularly scheduled intervals.
The tool is not repairable and should be replaced
when it is worn or damaged. Store the extraction tool
in a clean, dry place and clean the extraction tool with
a soft, lint--free cloth.
Additional tools can be purchased from:
CUSTOMER SERVICE (38--25)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
5. REVISION SUMMARY
S Updated document to corporate requirements
S New logo
E 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1--800--722--1111
PRODUCT INFORMATION 1--800--522--6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 1
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 3430-1000 | DISCRETE WIRE INSERTION TOOL |
| 3430-2000 | DISCRETE WIRE HAND TOOL |
| 3430-4000 | HEADER ROLL PIN INSERTER |
| 350-MX23-2 | TOOL CRIMP FOR MX23 |
| 35177 | BLADES REPL FOR 35175 100/PK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 3-188398-0 | 功能描述:硬公制连接器 TYP A FXD BRD M/CON RoHS:否 制造商:TE Connectivity / AMP 系列:Z-Pack 产品类型:Receptacles 排数:5 位置/触点数量:110 安装角:Right 端接类型:Pin 外壳材料:Polyester 触点材料:Phosphor Bronze 触点电镀:Gold 类型: |
| 31884 | 功能描述:端子 RING 22-18G #10 RoHS:否 制造商:AVX 产品:Junction Box - Wire to Wire 系列:9826 线规:26-18 接线柱/接头大小: 绝缘: 颜色:Red 型式:Female 触点电镀:Tin over Nickel 触点材料:Beryllium Copper, Phosphor Bronze 端接类型:Crimp |
| 318842-1 | 功能描述:手工工具 EXTRACTION TOOL ASSY RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 3-188440-1 | 制造商:TE Connectivity 功能描述:CONN D-SUB PL 9 POS CRMP ST PRESS 9TERM - Bulk 制造商:TE Connectivity 功能描述:Standard Board Mount Connectors |
| 3-188440-2 | 制造商:TE Connectivity 功能描述:CONN D-SUB PL 9 POS ST TH - Bulk 制造商:TE Connectivity 功能描述:Standard Board Mount Connectors |
发布紧急采购，3分钟左右您将得到回复。