- 您现在的位置：买卖IC网 > PDF目录19077 > 3443-106N (3M)LOCATOR PLATE D-SUB PDF资料下载
参数资料
| 型号： | 3443-106N |
| 厂商： | 3M |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | LOCATOR PLATE D-SUB |
| 标准包装： | 1 |
| 系列： | * |
| 产品目录页面： | 39 (CN2011-ZH PDF) |
| 其它名称： | 0-00-54007-68101-4 00054007681014 05400768101 3443-106N-ND 3443106N 3M9429 5400768101 54007681014 80-6105-4829-1 80-610548291 80610548291 |
Preassembled Connector Assembly Procedure
Set-up
1. Adjust the end block according to the flange style and connector size. A
Thru-hole style : Rotate the end block so that the locating pin is facing the inside of the locator plate.
The pin has to be removed so that the end block can be rotated. Then reassemble the pin. The pin is
used to guide the platen during harness assembly. B
Floating bushing and threaded insert style:
Rotate the end block so that the locating pin is facing the outside of the locator plate.
2. Install the cable stop insert 3664-B. C
3. Install the cable guide on the mounting stud. Refer to the last page for the appropriate guide. D
4. Place the locator plate on the press and affix it using the locking screw provided.
5. Place the platen on the assembly press. Refer to the last page for the appropriate platen.
Assembly
1. Cut required cable length using one of the 3M cutting tools.
2. Remove the connector from the packing strip.
3. Slide the connector onto the guiding groove and into the end block. E
4. Slide the cable under the cable guide. If the cable should not enter into the connector smoothly, check the
flatness of the cable. F
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and cable guide, then remove completed assembly.
7
Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
Two-Piece Connector Assembly Procedure
Set-up
1. Follow steps 1, 4 and 5 of the preassembled set-up instructions.
Assembly
1. Grasp 3M ? Delta Cover Strip between thumb and forefinger. While holding the adjacent cover, pull laterally
away from strip leaving the adhesive with a smooth clean edge.
2. Press cable ribs into cover alignment grooves.
3. Visually inspect to insure that the cable is properly aligned and oriented into cover grooves.
4. Engage cable/cover subassembly with connector body. Place subassembly in the locator plate with the
connector body facing up.
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and remove the completed assembly.
7. Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
3
78-8133-3685-2-A
相关PDF资料 |
PDF描述 |
|---|---|
| A0143G | LAMP NEON 110V 16MM |
| OPA731W | LED WHITE 20/1WATT 6500K ARRAY |
| P51-100-G-L-P-5V-000-000 | SENSOR 100PSI M10-1.25 6H 1-5V |
| 1.90060.1370000 | LAMP FILAMENT 110-130V BA 9SBASE |
| P51-750-S-W-P-5V-000-000 | SENSOR 750PSIS 1/8 NPT 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 3443-107N | 功能描述:折皱器 SOCKET LOCATOR PLATE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 3443-110 | 功能描述:折皱器 LOCATOR PLATE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 3443-112 | 功能描述:折皱器 LOCATOR PLATE TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 3443-113 | 功能描述:折皱器 LOCATOR PLATES RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 3443-117 | 功能描述:折皱器 LOCATOR PLATES RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。