参数资料
| 型号： | 3664-B |
| 厂商： | 3M |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | CABLE STOP OPEN COVER-DELTA CONN |
| 产品培训模块： | Input/Output Connector Systems Primer |
| 标准包装： | 1 |
| 系列： | Delta |
| 附件类型： | 定位器板 |
| 适用于相关产品： | Delta 连接器，2 件 |
| 位置数： | 9 ~ 37 |
| 其它名称： | 05400745354 DE610005220 |
Preassembled Connector Assembly Procedure
Set-up
1. Adjust the end block according to the flange style and connector size. A
Thru-hole style : Rotate the end block so that the locating pin is facing the inside of the locator plate.
The pin has to be removed so that the end block can be rotated. Then reassemble the pin. The pin is
used to guide the platen during harness assembly. B
Floating bushing and threaded insert style:
Rotate the end block so that the locating pin is facing the outside of the locator plate.
2. Install the cable stop insert 3664-B. C
3. Install the cable guide on the mounting stud. Refer to the last page for the appropriate guide. D
4. Place the locator plate on the press and affix it using the locking screw provided.
5. Place the platen on the assembly press. Refer to the last page for the appropriate platen.
Assembly
1. Cut required cable length using one of the 3M cutting tools.
2. Remove the connector from the packing strip.
3. Slide the connector onto the guiding groove and into the end block. E
4. Slide the cable under the cable guide. If the cable should not enter into the connector smoothly, check the
flatness of the cable. F
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and cable guide, then remove completed assembly.
7
Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
Two-Piece Connector Assembly Procedure
Set-up
1. Follow steps 1, 4 and 5 of the preassembled set-up instructions.
Assembly
1. Grasp 3M ? Delta Cover Strip between thumb and forefinger. While holding the adjacent cover, pull laterally
away from strip leaving the adhesive with a smooth clean edge.
2. Press cable ribs into cover alignment grooves.
3. Visually inspect to insure that the cable is properly aligned and oriented into cover grooves.
4. Engage cable/cover subassembly with connector body. Place subassembly in the locator plate with the
connector body facing up.
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and remove the completed assembly.
7. Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
3
78-8133-3685-2-A
相关PDF资料 |
PDF描述 |
|---|---|
| 369-72MMX100M-TAN | TAPE SEALING BOX TAN 72MMX100M |
| 371-CLEAR-48MMX1500M | TAPE SEALING INDUST 48MMX1500M |
| 3710-CLEAR-48MMX100M | TAPE PACKAGING CLEAR 48MMX100M |
| 372-TAN-72MMX100M | TAPE SEALING BOX TAN 72MMX100M |
| 3723-CLEAR-72MMX50M-BULK | TAPE LOW TEMP SEALING 72MMX50M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 3665 | 功能描述:LED Lighting COBs, Engines, Modules LED Engine - White, Cool Linear Light Strip, Plug and Play 制造商:inspired led, llc 系列:- 包装:- 零件状态:有效 类型:LED 引擎 颜色:冷白色 CCT（K）:6000K 波长:- 配置:线性灯条，即插即用 通量 @ 电流/温度 -测试:- 电流 - 测试:- 温度 - 测试:- 电压 - 正向（Vf）（典型值）:12V 不同测试电流时的流明/瓦:- 电流 - 最大值:- CRI（高显色指数）:- 视角:- 特性:- 大小/尺寸:- 高度:- 发光面（LES）:- 透镜类型:- 标准包装:1 |
| 36650 | 功能描述:L-KEY TORX LONG ARM T10 RoHS:否 类别:工具 >> 螺钉和螺母驱动器 系列:- 标准包装:1 系列:- 类型:六角扳手（内六角扳手）- 偏移 尺寸:0.098"（2.5mm） 特点:- 长度 - 叶片:0.70"（18mm） 长度 - 总体:2.17"（55mm） 重量:0.01 磅（4.54g） 其它名称:35112WI |
| 36650-1003 | 制造商:Amphenol RF 功能描述: |
| 36-6501-20 | 制造商:Aries Electronics Inc 功能描述:501 DIP TEST SCKT SOLDER TAIL |
| 36-6501-21 | 制造商:Aries Electronics Inc 功能描述:501 DIP TEST SCKT SOLDER TAIL |
发布紧急采购，3分钟左右您将得到回复。