- 您现在的位置：买卖IC网 > Datasheet目录794 > 386851 (Multicore)63/37 CRYSL 502 2% .022DIA/24SWG Datasheet资料下载
参数资料
| 型号： | 386851 |
| 厂商： | Multicore |
| 文件页数： | 1/2页 |
| 文件大小： | 0K |
| 描述： | 63/37 CRYSL 502 2% .022DIA/24SWG |
| MSDS 材料安全数据表： | MM00975 MSDS |
| 标准包装： | 20 |
| 系列： | C502 |
| 制程： | 有引线 |
| 类型： | 焊线 |
| 焊剂类型： | 免清洁 |
| 复合体： | Sn63Pb37（63/37） |
| 线规： | 24 |
| 直径： | 0.022"（0.56mm） |
| 芯体尺寸： | 2% |
| 形态： | 线轴，454g（1 磅） |
| 融点： | 361°F（183°C） |
| 其它名称： | 82-129 MM00975 |
Technical Data Sheet
C502
December - 2009
PRODUCT DESCRIPTION
C502 provides the following product characteristics:
Technology Solder wire - Cored
Activity Medium
Product Benefits ? No clean
Soldering Iron:
● Good results can be obtained using a range of tip
temperatures. However, the optimum tip temperature and
heat capacity required for a hand-soldering process is a
function of both soldering iron design and the nature of
the task.
IPC/J-STD-004
Classification
Application
Surface Finishes
? Clear residue
? Good wetting
? Fast soldering
? Mild odor
? Pb-free and SnPb alloys available
ROM1
Soldering
Copper, Brass and Nickel
● Care should be exercised to avoid unnecessarily high tip
temperatures for extensive periods of time.
● A high tip temperature may increase any tendency to flux
spitting and it may produce some residue darkening.
● The tip of the soldering iron should be properly tinned.
Severely contaminated soldering iron tips should be
cleaned with Multicore? Tip Tinner/Cleaner.
● Wipe the tip on a clean, damp sponge before re-tinning
with C502 wire.
C502 cored solder wire has been specially formulated to
complement no clean wave and reflow soldering processes.
C502 is also well suited for soldering applications requiring
high melting temperature alloys.
TYPICAL PROPERTIES
Solder Cored Wire
Alloys - Tin/lead ? SN63
? SN60
? SN62
Soldering Process:
1. Apply the soldering iron tip to the work surface. The iron
tip should contact both the base material and the lead at
the same time to heat both surfaces properly. It should
take no more than a fraction of a second to heat both
surfaces adequately.
2. Apply C502 flux cored wire to a part of the joint surface
away from the soldering iron and allow to form a joint
fillet. This will be virtually instantaneous. Do not apply
excessive solder to the joint as this will not improve joint
integrity and it will leave excess flux residues on the
surface.
Alloys - Lead Free
? 96SC (SAC387)
? 97SC (SAC305)
3. Remove solder from the work piece and then remove the
iron tip.
? 99C (SnCu)
? 95A (SnSb)
? 96S (SnAg)
Acid Value 156 to 172 mg KOH/g
Halide content 0.2%
Flux Content (%) 2.7
ALLOYS:
The alloys used in C502 cored solder wires conform to the
purity requirements of the common national and international
standards.
FLUX:
C502 solid flux is based on modified rosin and carefully
selected activators. In practice they exhibit a mild rosin odor
and leave a small quantity of clear residue.
DIRECTIONS FOR USE
Soldering with C502 does not require any special methods or
deviation from standard hand soldering practices.
4. The total process will be very rapid, depending upon
thermal mass, tip temperature, tip configuration and the
solderability of the surfaces to be joined.
5. The resin and flux systems are designed to leave
relatively low residues and to minimize residual activity.
This is achieved by ensuring some decomposition and
volatilization takes place during the soldering process
Cleaning:
C502 flux cored solder wire has been formulated to leave
amber flux residues and resist spitting and fuming. In most
industrial and consumer electronics applications, cleaning will
not be required. The product may, therefore, be used to
complement a no-clean wave soldering or reflow process or to
allow repairs to cleaned boards without the need for a second
cleaning process. In high-reliability applications, the residues
should be removed.
Should cleaning be required, this is best achieved using
SC-01? cleaner.
相关PDF资料 |
PDF描述 |
|---|---|
| 38L322C | INDUCTOR 3.20UH 7.80A SMD |
| 390-389TZ | BATT SILVER OXIDE BUTTON 1.55V |
| 392-384TZ | BATT SILVER OXIDE BUTTON 1.55V |
| 393-309TZ | BATT SILVER OXIDE BUTTON 1.55V |
| 397-396TZ | BATT SILVER OXIDE BUTTON 1.55V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 386857 | 功能描述:63/37 CRYSL 400 3% .032DIA/21SWG RoHS:否 类别:焊接、脱焊、返修产品 >> 焊接 系列:C400™ 标准包装:1 系列:- 制程:有引线 类型:焊线 焊剂类型:- 复合体:Sn60Pb40（60/40） 线规:- 直径:0.03"（0.76mm） 芯体尺寸:- 形态:线轴，227g（1/2 磅） 融点:361°F（183°C） 装运信息:- |
| 386859 | 制造商:3M Electronic Products Division 功能描述:CLOTH BELT 100X915 P120 |
| 386860 | 制造商:3M Electronic Products Division 功能描述:CLOTH BELT 50X1525 P80 |
| 3868-6000 | 功能描述:集管和线壳 8/SKT/OP/30AVG RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 386862 | 功能描述:63/37 CRYSL 502 2% .032DIA/21SWG RoHS:否 类别:焊接、脱焊、返修产品 >> 焊接 系列:C502 标准包装:1 系列:- 制程:有引线 类型:焊线 焊剂类型:- 复合体:Sn60Pb40（60/40） 线规:- 直径:0.03"（0.76mm） 芯体尺寸:- 形态:线轴，227g（1/2 磅） 融点:361°F（183°C） 装运信息:- |
发布紧急采购，3分钟左右您将得到回复。