- 您现在的位置：买卖IC网 > PDF目录18356 > 3EXM4S (TE Connectivity)MODULE POWER ENTRY 3A FCC 4V SW PDF资料下载
参数资料
| 型号： | 3EXM4S |
| 厂商： | TE Connectivity |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | MODULE POWER ENTRY 3A FCC 4V SW |
| 其它有关文件： | Corcom EMI/RFI Filter Selector Chart |
| 3D 型号： | 6609131-9.pdf |
| 标准包装： | 4 |
| 系列： | M |
| 保险丝盒： | 包括在内 |
| 安装类型： | 面板安装，螺孔 |
| 滤波器类型： | 辐射滤波器，FCC-B |
| 特点： | 保险丝盒，开关，通/断，不发光，电压选择器 |
| 电压： | 120VAC |
| 电流： | 3A |
| 端接类型： | 快速连接 |
| 类型： | IEC 320-C14（公引脚） |
| 其它名称： | 1609131-3 1609131-9 6609131-9 CCM1031 |
Catalog: 1654001
M Series
Corcom Product Guide
Slim Power Entry Module Family with Multiple Options
Issue Date: 06.2011
(continued)
Accessories (continued)
Fuse Installation Instructions
MA601 - 604: Insulating Boot
Plastic shroud for back of M series to prevent
inadvertent access to connections
1. Remove power cord
2. Insert a pocket screwdriver at point “X” as shown
MA601: Fits M4S versions
MA602: Fits M1S versions
MA603: Fits M4 versions
A
USE ONLY WITH
250V FUSES
DISCONNECT POWER
BEFORE REPLACING FUSES
Section A-A
MA604: First M1 versions
Voltage Selection
1. Open cover, using small blade screwdriver or
similar tool (see illustration on right)
2. Set aside cover/fuse block assembly
3. Pull voltage selector card straight out of housing,
using indicator pin
4. Orient selector card so that desired voltage is
readable at the bottom
5. Orient indicator pin to point up when desired
voltage is readable at bottom (note that when indi-
cator pin is ?xed, successive voltages are selected by
rotating the card 90° clockwise)
6. Insert voltage selector card into housing, printed
side of card facing forward toward IEC connector
and edge containing the desired voltage ?rst
7. Replace cover, and verify that indicator pin shows
the desired voltage
“X”
A
3. Gently lift the entire door UP approximately 1/4" (minimum)
Once lifted, the door will pivot on it’s hinges to expose
the fuse holder
Lift Up
4. When the fuse holder is installed in the single fuse position,
apply the screwdriver as shown and gently lift up
Use screwdriver as shown, do not use ?ngers
NOT here
Insert Here
When the fuse holder is installed in the dual fuse position,
it will normally release as soon as the door is opened
5. Install one (1) AG fuse or two (2) metric fuses (see below)
6. Replace fuse holder into housing
7. Swing and push to snap door back in place
Fuse Options
3
1
0
0
1
2
0
100V
0
0
120V
North American
single fuse installation
Metric
dual fuse installation
2
3
0
2
4
0
Install fuses on one side only, do not install
230V
240V
both AG and metric fuses at the same time
185
Dimensions are in inches and millimeters unless otherwise speci?ed. Values in italics
are metric equivalents. Dimensions are shown for reference purposes only.
Speci?cations subject to change.
For email, phone or live chat, please go to
te.com/help
corcom.com
相关PDF资料 |
PDF描述 |
|---|---|
| FVXO-HC73B-70.656 | OSC 70.656 MHZ 3.3V HCMOS SMD |
| 445W3XF25M00000 | CRYSTAL 25.000000 MHZ 24PF SMD |
| FVXO-HC73B-72.6 | OSC 72.6 MHZ 3.3V HCMOS SMD |
| 445W3XF24M57600 | CRYSTAL 24.576000 MHZ 24PF SMD |
| 445W3XF24M00000 | CRYSTAL 24.000000 MHZ 24PF SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 3EXP | 功能描述:电源线滤波器 3A PRINT CIRCUIT MNT PCB MOUNT RoHS:否 制造商:EPCOS 电压额定值:277 VAC 电流额定值:100 A 安装风格:Chassis 端接类型:Screw |
| 3EXP_11 | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:Chassis or PC Board Mountable Power Line Filters for Emission Control |
| 3EYP | 功能描述:电源线滤波器 3A PRINT CIRCUIT MNT PCB MOUNT RoHS:否 制造商:EPCOS 电压额定值:277 VAC 电流额定值:100 A 安装风格:Chassis 端接类型:Screw |
| 3EZ | 制造商:EIC 制造商全称:EIC discrete Semiconductors 功能描述:SILICON ZENER DIODES |
| 3EZ1 | 功能描述:电源线滤波器 3A FASTON FLANGE MNT RoHS:否 制造商:EPCOS 电压额定值:277 VAC 电流额定值:100 A 安装风格:Chassis 端接类型:Screw |
发布紧急采购，3分钟左右您将得到回复。