参数资料
| 型号： | 40IMX15-05-8R |
| 厂商： | Power-One |
| 文件页数： | 15/15页 |
| 文件大小： | 0K |
| 描述： | CONVERT DC/DC 15W 5V |
| 标准包装： | 6 |
| 系列： | * |
IMX70, IMY70 Series Data Sheet
70 to 90 Watt DC-DC Converters
Note: Other cleaning liquids may damage the adhesive joints of the
ferrite cores.
Isolation
The electric strength test is performed in the factory as a
routine test in accordance with EN 50116, IEC/EN 60950-1,
and UL/CSA 60950-1, and should not be repeated in the field.
Power-One will not honor any warranty claims resulting from
electric strength field tests.
Table 15: Electric strength test voltages
Characteristic
Factory test >1 s
Equivalent DC voltage
Insulation resistance
Input to
(outputs+case)
20/40I MX70 1
1.5 2
2.1
>100
Input to
(outputs+case)
110I MY70 1
3
4.2
>100
Outputs to
case
all models 1
0.5
0.7
–
Between
outputs
all models
0.15 3
0.21 3
–
Unit
kVAC
kVDC
M ?
at 500 VDC
1
2
3
For open-frame models (option Z), only the insulation input to outputs is tested.
1.5 kVAC according to IEC 60950, sect. 6.2, Telecom equipment; type test with 1.5 kVAC / 60 s (IEE 802.3).
The test voltage between outputs is not applied as routine test.
Options
Option i: Inhibit (Negative Shutdown Logic)
The output of the converter may be enabled or disabled by
pin 8. No output voltage overshoot will occur, when the
converter is turned on. If the inhibit function is not required the
inhibit pin 8 should be connected to Vi– to enable the output
(active low logic, fail safe). Voltage on pin 8:
means of a logic signal (TTL, CMOS, etc.) applied to the inhibit
06138a
4 Vi+
Converter operating:
Converter disabled:
Option Z
–10 V to +0.8 V
2.4 V to 20 V
If the converters are mounted onto a mother board, in many
Fig. 17
8 i
2 Vi –
cases, a converter case is not required. Only converters with
option Z are not varnished, and this allows dipping of the
populated board including the converter into a protection
lacquer.
Note : The converters shall not be exposed to cleaning processes,
as this will damage the glue of the ferrite cores.
If the inhibit function is not used, the inhibit pin should be
connected to Vi–.
NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical
components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written
consent of the respective divisional president of Power-One, Inc.
TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on
the date manufactured. Specifications are subject to change without notice.
BCD.00002 Rev AF, 18-Dec-2013
MELCHER
The Power Partners.
Page 15 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| MC10E137FN | IC RIPPLE COUNTER 8BIT HS 28PLCC |
| MC74LVXU04DTR2 | IC INVERTER HEX UNBUFFER 14TSSOP |
| MC10E136FN | IC COUNTER U/D 6BIT UNIV 28-PLCC |
| SQM48T20010-PAAP | DC/DC EIGHTH BRICK |
| MC100EP33MNR4 | IC DIVIDER BY4 ECL CLK IN 8-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 40IMX15-05-8RG | 功能描述:DC/DC转换器 15W (5V) DC Input (16.8-75V) RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| 40IMX15-05-8RG-G | 功能描述:DC/DC CONVERT 5.1V 3.5A 制造商:bel power solutions 系列:* 零件状态:新产品 标准包装:12 |
| 40IMX15-05-9R | 制造商:Power-One 功能描述: |
| 40IMX15-05-9RG | 制造商:Power-One 功能描述: |
| 40IMX15-12-12-8 | 功能描述:DC/DC转换器 15W (2x 12V) DC Input (16.8-75V) RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。