- 您现在的位置：买卖IC网 > PDF目录21904 > 4320-DKDB5 (Silicon Laboratories Inc)KIT DEV TEST EZRADIO SI4320 RX PDF资料下载
参数资料
| 型号： | 4320-DKDB5 |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 3/36页 |
| 文件大小： | 0K |
| 描述： | KIT DEV TEST EZRADIO SI4320 RX |
| 标准包装： | 1 |
| 附件类型： | 测试卡，接收器，868MHz |
| 适用于相关产品： | EZRadio? |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Si4320
DQD
The Data Quality Detector monitors the I/Q output of the
baseband amplifier chain by counting the consecutive correct 0-
>1, 1->0 transitions. The DQD output indicates the quality of the
signal to be demodulated. Using this method it is possible to
"forecast" the probability of BER degradation. The programmable
DQD parameter defines the threshold for signaling the good/bad
data quality by the digital one-bit DQD output. In cases when the
deviation is close to the bitrate, there should be four transitions
during a single one bit period in the I/Q signals. As the bitrate
decreases in comparison to the deviation, more and more
transitions will happen during a bitperiod.
AFC
By using an integrated Automatic Frequency Control (AFC)
feature, the receiver can synchronize its local oscillator to the
received signal, allowing the use of:
? inexpensive, low accuracy crystals
Event Handling
In order to minimize current consumption, the receiver supports
the sleep mode. Active mode can be initiated by several wake-up
events (wake-up timer timeout, low supply voltage detection, on-
chip FIFO filled up or receiving a request through the serial
interface).
If any wake-up event occurs, the wake-up logic generates an
interrupt signal, which can be used to wake up the
microcontroller, effectively reducing the period the
microcontroller has to be active. The cause of the interrupt can
be read out from the receiver by the microcontroller through the
SDO pin.
Interface and Controller
An SPI compatible serial interface lets the user select the
frequency band, center frequency of the synthesizer, and the
bandwidth of the baseband signal path. Division ratio for the
microcontroller clock, wake-up timer period, and low supply
?
?
narrower receiver bandwidth (i.e. increased sensitivity)
higher data rate
voltage detector threshold are also programmable. Any of these
auxiliary functions can be disabled when not needed. All
parameters are set to default after power-on; the programmed
Crystal Oscillator
The chip has a single-pin crystal oscillator circuit, which provides
a 10 MHz reference signal for the PLL. To reduce external parts
and simplify design, the crystal load capacitor is internal and
programmable. Guidelines for selecting the appropriate crystal
can be found later in this datasheet. The receiver can supply the
clock signal for the microcontroller, so accurate timing is possible
without the need for a second crystal.
When the microcontroller turns the crystal oscillator off by
clearing the appropriate bit using the Configuration Setting
Command, the chip provides a fixed number (128) of further
clock pulses (“clock tail”) for the microcontroller to let it go to idle
or sleep mode.
Low Battery Voltage Detector
The low battery detector circuit monitors the supply voltage and
generates an interrupt if it falls below a programmable threshold
level. The detector circuit has 50 mV hysteresis.
Wake-Up Timer
The wake-up timer has very low current consumption (1.5 μA
typical) and can be programmed from 1 ms to several days with
an accuracy of ±10%.
values are retained during sleep mode. The interface supports
the read-out of a status register, providing detailed information
about the status of the receiver and the received data. It is also
possible to store the received data bits into the 16bit RX FIFO
register and read them out in a buffered mode. FIFO mode can
be enabled through the SPI compatible interface by setting the fe
bit to 1 in the Output and FIFO Mode Command.
Standalone Operation Mode
The chip also provides a standalone mode, which allows the use
of the receiver without a microcontroller. This mode can be
selected by connecting the CLK/LPDM pin to either VDD or VSS.
After power on, the chip will check this pin. If it is connected to
any supply voltage, then the chip will go to standalone mode.
Otherwise, it will go to microcontroller mode and the pin will
become an output and provide a clock signal for the
microcontroller. To prevent the Si4320 from accidentally entering
a standalone mode, the stray capacitance should be kept below
50 pF on pin 8.
In this mode operating parameters can be selected from a
limited set by “programming” the receiver over its pins. The chip
is addressable and four digital output pins can be controlled by
the received data. Selecting the Low Power Duty-Cycle Mode
(LPDM) the chip consumes less than 0.5 mA average current.
It calibrates itself to the crystal oscillator at every startup. When
the crystal oscillator is switched off, the calibration circuit
switches it back on only long enough for a quick calibration (a
few milliseconds) to facilitate accurate wake-up timing.
3
相关PDF资料 |
PDF描述 |
|---|---|
| 4320-DKDB4 | KIT DEV TEST EZRADIO SI4320 RX |
| PSL0101WBFD1 | LED WHITE 90LM 350MA 3000K SSML |
| PSL0101WBFB1 | LED WHITE 80LM 350MA 3000K SSML |
| V600-IDSC02 | V600 CTRL 2 CH |
| PSL0102WBEC1 | LED WHITE 30LM 120MA 5000K SSML |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4320-DKDB8 | 功能描述:射频开发工具 Test Board xloop Rx (915MHz) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4320-DKDB9 | 功能描述:射频开发工具 Test Board xloop Rx (868Mhz) RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 4320-L15 | 制造商:American Denki 功能描述: |
| 4320-P | 制造商:American Denki 功能描述: |
| 4320PA51G01800 | 功能描述:GK,NICU,NRSG,PU,V0,DSH 制造商:laird technologies emi 系列:- 零件状态:有效 形状:D 形 厚度 - 总:0.050"（1.30mm） 宽度:0.140"（3.60mm） 长度:18.000"（457.20mm） 粘合剂:- 温度范围:- 标准包装:105 |
发布紧急采购，3分钟左右您将得到回复。