- 您现在的位置：买卖IC网 > Datasheet目录598 > 45439 (TE Connectivity)TOOL DIE SOLIS 69099 2/0AWG Datasheet资料下载
参数资料
| 型号： | 45439 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/8页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SOLIS 69099 2/0AWG |
| 标准包装： | 1 |
| 系列： | * |
| 相关产品： | 1752868-1-ND - HYDRAULIC CRIMP C-HEAD |
408- 1697
Crimping Head 69097
Lock Screw
Retaining Ring
Shank
Stationary Die
Moving Die
Ram Locking
Screw
Figure 2
Crimping Head 69099
(Die Set 69218 Shown)
Lock Screw
Stationary Die
Moving Die
Flat on Shank
Faces Lock Screw
Ram Locking
Screw
Figure 3
i
NOTE
i
Lock screws in the top section of the crimping
head and in the ram are not used when installing
dies with retaining rings on shanks.
NOTE Ensure that the dies are inserted “fully” and that
the “flats” on the shanks are facing the lock
screws.
3. Loosen the ram lock screw and insert the shank
of the moving die into the ram well. Tighten the
lock screw. See Figure 3.
2. Insert the shank of the stationary die into the top
section of the crimping head. See Figure 2. The
retaining clip will hold the die in place.
3. Activate the power unit to advance the ram until
the lock screw is visible.
4. Loosen the lock screw and insert the shank of
the moving die into the ram well. See Figure 2. The
retaining ring will hold the die in place.
5. Activate the power unit to complete the cycle
and allow the ram to return to the “DOWN”
position.
B. Crimping Head 69099
1. Loosen the lock screw in the top section of the
crimping head. See Figure 3.
2.2. Die Removal
In crimping head 69097, insert the screwdriver blade
under the base of the stationary and moving dies.
Apply a prying action to loosen and remove the dies.
In crimping head 69099, loosen the lock screws in the
top section of the crimping head and ram and remove
the dies.
2.3. Wire Stripping and Crimping Procedures
A. Wire Stripping Procedure
Strip the wire to the dimensions shown in the table
in Figure 1.
CAUTION Do not nick or cut the conductor strands.
!
B. Crimping Procedure
2. Insert the shank of the stationary die into the top
section of the crimping head and tighten the lock
screw. See Figure 3.
2 of 8
DANGER
Avoid personal injury. When operating the power
unit, exercise caution while holding terminals,
splices, or wire near the crimping area.
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 45575-1 | DAHT PG BUTT 14-22 |
| 455822-2 | EXTRACTION TOOL MINI RECT CONN |
| 458139-1 | ANVIL SPECIAL |
| 4600-01V04BB999 | TRANSFORMER |
| 46468 | CRIMP HAND TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 45-4395 | 制造商:GC Electronics 功能描述: |
| 454398-1 | 制造商:TE Connectivity 功能描述:ROD, FEED - Bulk |
| 454398-2 | 功能描述:手工工具 ROD, FEED RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 45439-SLATE-BULK | 制造商:Alpha Wire 功能描述: |
| 4543B | 制造商:NTE Electronics 功能描述: |
发布紧急采购，3分钟左右您将得到回复。