参数资料
| 型号： | 4955-WHITE-1"X36YD |
| 厂商： | 3M |
| 文件页数： | 8/11页 |
| 文件大小： | 0K |
| 描述： | TAPE VHB ACRYLIC FOAM 1"X 36YD |
| 视频文件： | 3M VHB adhesive demonstration - Another Geek Moment |
| MSDS 材料安全数据表： | 4955 MSDS |
| 标准包装： | 9 |
| 系列： | VHB™ 4955 |
| 胶带类型： | 双涂层，双面 |
| 胶合剂： | 丙烯酸 |
| 背衬，载体： | 聚酯薄膜 |
| 厚度： | 0.080"（80 mils，2.032mm） |
| 厚度 - 胶合剂： | 0.078"（78 mils，1.981mm） |
| 厚度 - 背胶，载体，衬垫： | 0.0020"（2.0 mils，0.051mm） |
| 宽： | 1.00"（25.40mm） |
| 长度： | 108'（32.9m）36 码 |
| 颜色： | 白 |
| 使用： | 通用 |
| 温度范围： | 300°F（149°C） |
| 其它名称： | 00021200675010 02120067501 70006097136 |
3M ? VHB ? Tapes
Design and Tape Selection Considerations
Choose the right tape for the substrate: Adhesives must flow onto the substrate surfaces in order to achieve intimate
contact area and allow the molecular force of attraction to develop. The degree of flow of the adhesive on the substrate
is largely determined by the surface energy of the substrate.
Adhesive
High surface energy
— Substrate
Adhesive
— Substrate
Low surface energy
This illustration demonstrates the effect of surface energy on adhesive interfacial contact. High surface energy
materials draw the adhesive closer for high bond strength.
Relationship of Adhesion and Surface Energy for 3M? VHB? Tape Adhesive Families
100%
NOTE: Low surface energy
adhesive may be less
affected by surface energy.
en
al
pe
ra
Pu
os
Ad
Ad
he
ve
50%
Lo
w
Te
G
m
er
tu
re e
rp
si
he
si
ve
M
ul
ti-
Pu
rp
os
e
Ad
he
si
ve
NOTE: Foam type can
affect and/or limit maximum
adheisve strength.
0%
Surface Energy (Dynes/cm)
HIGH
MEDIUM
LOW
400-1100
Aluminum
Stainless Steel
Copper
Zinc
Tin
Lead
Anodized Aluminum
42-50
Kapton ?
Phenolic
Nylon
Alkyd Enamel
Polyester
Epoxy Paint
Polyurethane
38-39
ABS
Polycarbonate (Lexan ? )
PVC
Noryl ?
Acrylic
Polane ? Paint
Powder Paint
36-37
PVA
Polystyrene
Acetal
Kynar ? Paint
Powder Paint
18-33
EVA
Polyethylene
Polypropylene
Tedlar ?
Silicone
PTFE
Glass
NOTES: There are a wide variety of formulations, surfaces finishes and surface treatments available on substrate materials which can affect adhesion. This chart is intended
to provide only a rough estimate of the adhesion levels which can be expected on some common materials relative to a reference surface such as aluminum.
Light abrasion of surface will significantly increase adhesion levels on many materials, except when using tapes 4952/4932.
Use the right tape thickness: The necessary thickness of tape depends on the rigidity of substrates and their flatness
irregularity. While the 3M? VHB? Tapes will conform to a certain amount of irregularity, they will not flow to fill
gaps between the materials. For bonding rigid materials with normal flatness, consider use of tapes with thickness of 45
mils (1.1 mm) or greater. As the substrate flexibility increases thinner tapes can be considered.
Use the right amount of tape: Because 3M? VHB? Tapes are viscoelastic by nature their strength and stiffness is a
function of the rate at which they are stressed. They behave stronger with relatively faster rate of stress load (dynamic
stresses) and will tend to show creep behavior with stress load acting over a long period of time (static stresses). As a
general rule, for static loads, approximately four square inches of tape should be used for each pound of weight to be
supported in order to prevent excessive creep. For dynamic loads, the dynamic performance characteristics provided
on page 4 should be useful, factoring in the appropriate safety factors.
Allow for thermal expansion/contraction: 3M? VHB? Tapes can perform well in applications where two bonded
surfaces may expand and contract differentially. Assuming good adhesion to the substrates, the tapes can typically
tolerate differential movement in the shear plane up to 3 times their thickness.
Bond Flexibility: While an advantage for many applications where allowing differential movement is a benefit, the
tape bonds are typically more flexible than alternative bonding methods. Suitable design modifications or periodic use
of rigid fasteners or adhesives may be needed if additional stiffness is required.
Severe Cold Temperature: Applications which require performance at severe cold temperatures must be thoroughly
evaluated by the user if the intended use will subject the tape product to high impact stresses. A technical bulletin
“3M? VHB? Tape Cold Temperature Performance” (70-0707-3991-0) is available for additional information.
-8-
相关PDF资料 |
PDF描述 |
|---|---|
| AN-2858 | BOX ALUM 8.75X5.75X3.25" NAT |
| 6162.0058 | 6061 APPLIANCE INLET 10A 70C |
| PN-1335-DG | BOX NEMA4X ABS 10.43X7.28X 3.74" |
| 983-32-2"X50YD-6RL | CONSPICUITY MARKING 2" RED/WHT |
| 6162.0057 | 6061 APPLIANCE INLET 10A 70C |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4955-WHITE-3/4"X36YD | 功能描述:TAPE VHB ACRYLIC FOAM 3/4"X 36YD RoHS:是 类别:胶带，粘合剂 >> 带 系列:VHB™ 4955 MSDS 材料安全数据表:42x, 43x, 140x, 141x, 1449, 1450, 433,438,33xx MSDS 标准包装:1 系列:425 胶带类型:铝箔 胶合剂:丙烯酸 背衬，载体:铝，极软的 厚度:0.0046"（4.6 mils，0.117mm） 厚度 - 胶合剂:0.0016"（1.6 mils，0.041mm） 厚度 - 背胶，载体，衬垫:0.0028"（2.8 mils，0.071mm） 宽:2.00"（50.80mm） 长度:15'（4.6m）5 码 颜色:银 使用:热耗散，反射 温度范围:-65 ~ 300°F（-54 ~ 149°C） 包装:散装 工具箱:3M10454-ND - MRO TAPE KIT - PREMIUM3M10451-ND - MRO TAPE KIT - STANDARDTK3434-ND - HOME TAPE KIT - PREMIUM3M10395-ND - DESIGN ENGR SOLUTION SEMINAR KIT3M10394-ND - DESIGN ENGR METAL FOIL TAPE KIT 其它名称:3M9778 |
| 4955-WHITE-3/4X36YD | 制造商:3M Electronic Products Division 功能描述: |
| 4956 | 功能描述:射频适配器 - 系列之内 TYPE N TO TYPE N RoHS:否 制造商:Amphenol Connex 射频系列:SMA 侧1性别:Jack (Female) 侧1极性:Normal 侧2性别:Jack (Female) 侧2极性:Normal 阻抗:50 Ohms 主体类型:Bulkhead 适配器类型:Straight 频率范围:DC to 18 GHz 触点电镀:Gold 外壳电镀:Gold 主体材料:Brass |
| 4956 GRAY 3/4 IN X 36 YD | 制造商:3M Electronic Products Division 功能描述:70006161767 4956 3/4 X 36 YD BULK |
| 4956 1" | 功能描述:胶带 1"X36YD GRAY FOAM RoHS:否 制造商:3M Electronic Specialty 产品:Tapes 类型:Shielding 描述/功能:EMI/RFI Foil Shielding Tape 颜色: 材料:Copper Foil 宽度:1 in x 18 yds |
发布紧急采购，3分钟左右您将得到回复。