- 您现在的位置：买卖IC网 > PDF目录33843 > 4TPB220ML (National Semiconductor Corporation) N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages PDF资料下载
参数资料
| 型号： | 4TPB220ML |
| 厂商： | National Semiconductor Corporation |
| 英文描述： | N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages |
| 中文描述： | N沟道场效应管同步降压稳压控制器输出电压低 |
| 文件页数： | 12/22页 |
| 文件大小： | 602K |
| 代理商： | 4TPB220ML |
Connection Diagram
20049411
14-Lead Plastic TSSOP
θ
JA = 155C/W
NS Package Number MTC14
Pin Description
BOOT (Pin 1) - Supply rail for the N-channel MOSFET gate
drive. The voltage should be at least one gate threshold
above the regulator input voltage to properly turn on the
high-side N-FET.
LG (Pin 2) - Gate drive for the low-side N-channel MOSFET.
This signal is interlocked with HG to avoid shoot-through
problems.
PGND (Pins 3, 13) - Ground for FET drive circuitry. It should
be connected to system ground.
SGND (Pin 4) - Ground for signal level circuitry. It should be
connected to system ground.
V
CC (Pin 5) - Supply rail for the controller.
PWGD (Pin 6) - Power Good. This is an open drain output.
The pin is pulled low when the chip is in UVP, OVP, or UVLO
mode. During normal operation, this pin is connected to V
CC
or other voltage source through a pull-up resistor.
ISEN (Pin 7) - Current limit threshold setting. This sources a
fixed 50A current. A resistor of appropriate value should be
connected between this pin and the drain of the low-side
FET.
EAO (Pin 8) - Output of the error amplifier. The voltage level
on this pin is compared with an internally generated ramp
signal to determine the duty cycle. This pin is necessary for
compensating the control loop.
SS (Pin 9) - Soft start pin. A capacitor connected between
this pin and ground sets the speed at which the output
voltage ramps up. Larger capacitor value results in slower
output voltage ramp but also lower inrush current.
FB (Pin 10) - This is the inverting input of the error amplifier,
which is used for sensing the output voltage and compen-
sating the control loop.
FREQ (Pin 11) - The switching frequency is set by connect-
ing a resistor between this pin and ground.
SD (Pin 12) - IC Logic Shutdown. When this pin is pulled low
the chip turns off the high side switch and turns on the low
side switch. While this pin is low, the IC will not start up. An
internal 20A pull-up connects this pin to V
CC.
HG (Pin 14) - Gate drive for the high-side N-channel MOS-
FET. This signal is interlocked with LG to avoid shoot-
through problems.
LM2727/LM2737
www.national.com
2
相关PDF资料 |
PDF描述 |
|---|---|
| 4X16E43V | 4 MEG x 16 EDO DRAM |
| 4X16E83VTW-6 | 4 MEG x 16 EDO DRAM |
| 4X16E83V | 4 MEG x 16 EDO DRAM |
| 5-1437508-1 | TRANSISTOR SOCKET |
| 5-1437508-8 | TO-5, TRANSISTOR SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4TPB220ML | 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR 220UF 4V |
| 4TPB330ML | 功能描述:钽质电容器-SMD聚合物 4volts 330uF ESR 40mohm RoHS:否 制造商:Kemet 电容:33 uF 电压额定值:50 V ESR:40 mOhms 容差:20 % 工作温度范围: 外壳代码 - in:2917 外壳代码 - mm:7343 高度:4 mm 制造商库存号:X Case 系列:T543 产品: 封装:Reel |
| 4TPB330ML | 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR 330UF 4V |
| 4TPB470M | 制造商:SANYO 功能描述:CAPACITOR, 470UF, 4V 制造商:SANYO 功能描述:CAPACITOR, 470UF, 4V Bulk 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR 470UF 4V 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR, 470UF, 4V |
| 4TPB470M | 制造商:SANYO Semiconductor Co Ltd 功能描述:CAPACITOR 470UF 4V |
发布紧急采购，3分钟左右您将得到回复。