- 您现在的位置：买卖IC网 > Datasheet目录600 > 535072-1 (TE Connectivity)TOOL EURO TYPE C CONN INSERT Datasheet资料下载
参数资料
| 型号： | 535072-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL EURO TYPE C CONN INSERT |
| 标准包装： | 1 |
| 系列： | Eurocard |
| 工具类型： | 插入工具 |
| 适用于相关产品： | 插座连接器 |
408- 9623
!
3.2. Application Tooling
The seating tool is designed for use with an applicator
assembly, or similar manual machine with sufficient
ram surface and the capability of applying a maximum
insertion force of 178 N [40 lbs] per contact.
A pneumatic machine can also be used, provided the
equipment has positive shut--height stops.
3.3. Seating Height
The seating height—the distance from the bottom
surface of the ram to the top of the pc board when
the ram is fully DOWN—must be set at the dimension
given in Figure 2 before starting the seating
procedure. The shut height equals the seating height
plus the combined thickness of the pc board and pc
board support fixture. See Figure 2.
4. SEATING PROCEDURE
When setting up equipment to seat connectors, pay
particular attention to the following:
— make sure that the number of rows and
positions in the connector is identical to the
number of rows and position of rectangular blades
of the seating tool (refer to Figure 1)
— be sure that the seating tool and connector are
properly aligned and set (refer to Figure 2) before
cycling the application tooling
CAUTION If the seating tool and connector are improperly
aligned in the equipment, damage could occur to
the tooling, connector, or both.
After the tool has been installed and the equipment
has been set up with the pc board support fixture in
place, proceed as follows:
1. Place the pc board with the proper hole pattern
onto the pc board support fixture.
2. Insert the contacts of the connector into the pc
board holes until the compliant pin area of each
contact starts to enter its pc board hole.
3. Position the side plates of the seating tool over
the connector to be seated.
4. Center the seating tool and connector under the
push surface of the ram.
5. Lower the ram slowly and verify the alignment of
the seating tool to the connector.
6. Apply force to the push plate of the seating tool
to seat the connector onto the pc board.
7. Manually retract the ram, and carefully remove
the seating tool.
8. Continue seating connectors as described until
all connectors have been seated.
Applicator Ram (Down)
Push Plate of Seating Tool
2 of 3
Applicator
Shut Height
Seating Height
(Connector Seated)
38.1+0.25/-- .000 mm
[1.50+.010/-- .000 in.]
Figure 2
Side Plates of Seating Tool
PC Board
PC Board Support Fixture
Rev E
相关PDF资料 |
PDF描述 |
|---|---|
| 539758-2 | DIE 2,8 TAB+EDS |
| 539960-1 | EXTRACTION TOOL FOR AP-963711-1 |
| 54200C | XFRMR CURR SENSE 15A 1:1:200 SMD |
| 543382-6 | TOOL INSERT/EXTRACT TIP 25-KIT |
| 543518-1 | TOOL COVER TERMINATOR IDC AMPMOD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 535074-1 | 功能描述:DIN 41612 连接器 EUROCARD SHROUD 96P RoHS:否 制造商:HARTING 系列:har-bus 64 产品类型:Plugs 排数:5 位置/触点数量:160 安装角:Right 类型:Shrouded Header 端接类型:Solder 外壳材料: 触点材料: 触点电镀: |
| 535074-2 | 功能描述:标准卡缘连接器 EURO SHROUD 96 POS RoHS:否 制造商:3M Electronic Solutions Division 系列:SPD08 产品类型:Contacts 位置/触点数量:60 安装角:Straight 电路板厚度: 安装风格:SMD/SMT 节距:8 mm 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Copper Alloy 触点电镀:Gold |
| 535079-5 | 功能描述:DIN 41612 连接器 RECPT 120P VERT TYPE C RoHS:否 制造商:HARTING 系列:har-bus 64 产品类型:Plugs 排数:5 位置/触点数量:160 安装角:Right 类型:Shrouded Header 端接类型:Solder 外壳材料: 触点材料: 触点电镀: |
| 53508 | 制造商:Thomas & Betts 功能描述:CONNECTOR,COMPRESSION 2 WAY 制造商:Thomas & Betts 功能描述:Splice Terminal 1AWG Electro-Tin |
| 535080-5 | 功能描述:DIN 41612 连接器 150P TYPE C DIN RECP RoHS:否 制造商:HARTING 系列:har-bus 64 产品类型:Plugs 排数:5 位置/触点数量:160 安装角:Right 类型:Shrouded Header 端接类型:Solder 外壳材料: 触点材料: 触点电镀: |
发布紧急采购，3分钟左右您将得到回复。