- 您现在的位置：买卖IC网 > Datasheet目录600 > 58082-1 (TE Connectivity)TOOL HEAD TERMINATING ONLY Datasheet资料下载
参数资料
| 型号： | 58082-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL HEAD TERMINATING ONLY |
| 标准包装： | 25 |
| 系列： | MTA-156 |
| 相关产品： | A2031-ND - TOOL MANUAL FOR SHELL CONNECTORS |
| 其它名称： | Q1066398 |
408-6795
Test Connector
Contact (Partially
Removed)
Production Connector
Improper Cut
Wire Retainer
(Removed)
Lance
Contact Slot
Front Beam
Right
Lead In
Wrong
Wrong
Deformation
Figure 2
3.2. For Pistol Grip Pneumatic Handle Assembly
1. Perform the procedure outlined in Paragraph 3.1,
for Pistol Grip Manual Handle Assembly, Steps 1
through 4.
2. Inspect termination to ensure that conductor is
terminated past the lead-in transition and is
positioned about halfway into the contact slot. See
Figure 2.
3. Inspect termination to ensure that insulation is
2.03 to 2.54 mm [.080-.100 in.] beyond the front
contact beam.
reduce the wire insertion depth by approximately
0.20 mm [.008 in.]. Repeat Steps 3, 4, and 5 or
Section 3, SETUP ADJUSTMENTS AND TEST.
Turn Clockwise to
Reduce Wire
Insertion Depth
4. If, upon inspection, it is determined that the wire
is not inserted deep enough, increase the air
pressure by 68.95 kPa [10 psi], and repeat the
termination and inspection procedure. Continue in
this manner until either the proper insertion depth is
obtained, or the air pressure is set to 482.6 kPa
Turn Counterclockwise
for Deeper Wire
Insertion
Adjuster
wrench or pliers; both of these tools will deform or
nick the adjuster.
[70 psi]. If the proper insertion depth is not reached
at 482.6 kPa [70 psi], return the air pressure to
275.8 kPa [40 psi] and follow the procedure in
Paragraph 3.3, Wire Insertion Depth Adjustment.
If the wire is inserted too deep, refer to the procedure
in Paragraph 3.3, Wire Insertion Depth Adjustment.
3.3. Wire Insertion Depth Adjustment
CAUTION Use a 9/16-in. socket wrench or box wrench when
turning the adjuster. Do NOT use an open-end
!
Wire Too Deep in Contact Slot - If the wire is inserted
too deep, remove the head, and turn the adjuster 1/6
revolution CLOCKWISE (see Figure 3). This will
Rev A
NOTE: 1/6 Turn Equals 0.20 mm [.008 in.] Adjustments.
Figure 3
4. TERMINATING PROCEDURE (Figure 4)
1. Insert connector into left side of head as
indicated.
2. Align contact to be terminated with wire inserter.
3. Make sure index pawl rests between connector
index ribs.
4. Insert an unstripped wire into the funnel area
between contact and wire inserter until it bottoms on
tool base.
2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 58238-1 | DIE SET SHELL SIZE 4-5 .375-.435 |
| 58246-2 | TOOL HEAD TERM MTA 100 W/O TL |
| 58336-1 | HEAD (IDC) MODU MTE W/O TL |
| 58338-1 | PWR BENCH ASSEMBLY W/O HEADS |
| 58372-1 | TOOL HEAD ASSEM 2MM TERMINATER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5808-2-10 | 制造商:Seastrom Mfg 功能描述: |
| 5808216 | 功能描述:电缆固定件和配件 Cable, ATEX, Short Seal, Gray RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 5808220 | 功能描述:电缆固定件和配件 Cable, ATEX, Short Seal, Gray RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 5808221 | 功能描述:电缆固定件和配件 Cable, ATEX, Short Seal, Gray RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 5808225 | 功能描述:电缆固定件和配件 Cable, ATEX, Short Seal, Gray RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
发布紧急采购，3分钟左右您将得到回复。