- 您现在的位置：买卖IC网 > Datasheet目录601 > 58483-1 (TE Connectivity)TOOL SMB DIE SET CONN MIL TYPE Datasheet资料下载
参数资料
| 型号： | 58483-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL SMB DIE SET CONN MIL TYPE |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III |
| 压接或电缆尺寸： | RG/U-161，174，179，187，188，316 |
| 压接手柄： | A9996-ND |
| 连接器类型： | SMB |
| 产品目录页面： | 453 (CN2011-ZH PDF) |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | A9968 |
The tool frame features a stationary jaw and handle, a
moving jaw, a moving handle, and an adjustable
ratchet that ensures full crimping. The tool frame
holds the die assembly.
The die assembly consists of an indenter (stationary
die) and an anvil (moving die). When closed, the dies
form three crimping chambers. Each die is held in the
hand tool frame by a single screw.
Make sure that the center contact is properly crimped
and assembled onto the connector as described in
applicable connector instruction sheet. Then proceed
as follows:
1. Slide the ferrule over the cable braid until it is
positioned against the shoulder of the plug body.
2. Close the tool handles until the ratchet releases,
then allow the handles to open FULLY.
3. Place the ferrule in the appropriate crimping
chamber on the anvil die so that the shoulder of
the plug body is close to the edge of the die. Refer
to Figure 3.
1. Close the tool handles until the ratchet releases,
then allow the handles to open fully.
2. Insert the dies into the tool jaws as shown in
Figure 2, and align the retaining holes in each die
with the associated hole in the tool.
Figure 3
4. While holding the assembly, close the tool
handles until the dies hold the ferrule in place.
5. Carefully close the tool handles until the ratchet
releases, then allow the handles to open FULLY.
Figure 2
3. Thread, but do not tighten, the die retaining
screws into the holes.
4. Carefully close the tool handles, making sure
that the dies align properly.
5. Tighten the die retaining screws with the
appropriate hex wrench.
6. To disassemble, close the tool handles until the
ratchet releases, remove the two die retaining
screws, and slide the dies out of the tool jaws.
6. Remove the ferrule from the dies.
7. Inspect the crimped ferrule according to
applicable connector instruction sheet. If
necessary, adjust the ratchet as described in
Section 5.
The tool ratchet mechanism features an adjustment
wheel with numbered settings. The adjustment wheel
controls the amount of handle pressure exerted on
the jaws during crimping. If the crimp is not
acceptable, adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
相关PDF资料 |
PDF描述 |
|---|---|
| 58500-1 | TOOL CRIMP SMB RG/174 W/DIE SET |
| 58509-1 | DIE SET 22-10AWG BUDGET |
| 58511-5 | FB 2MM ZPACK SEATING TOOL ASSY |
| 58514-2 | DIE SET MR CONN USE WITH A9996 |
| 58517-4 | TOOL PRO-CRIMPER II DIE SET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 584831-000 | 制造商:TE Connectivity 功能描述:Heat Shrink Molded Boot ST Flexible VPB 制造商:TE Connectivity 功能描述:202C611-50/86-0 - Bulk |
| 5-848407-2 | 功能描述:电缆组件 LGH 1/2 SGL END LEAD ASY GRN RoHS:否 制造商:Molex 产品:Power Assemblies 类型:Cable Assembly 连接器端口 A:No Connector 连接器端口 A 管脚计数:4 连接器端口 B:No Connector 连接器端口 B 管脚计数: 型式:Male 线规 - 美国线规（AWG）:20, 28 长度:0.305 m 颜色:Black, Red |
| 584850-000 | 制造商:TE Connectivity 功能描述:55/0114-24-9 - Cable Rools/Shrink Tubing |
| 58485-1 | 功能描述:冲压机与冲模 N TYPE DIE SET RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58485-2 | 功能描述:冲压机与冲模 Triple Stack USB A 5u DIM A=2.84 BEIGE RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。