- 您现在的位置：买卖IC网 > PDF目录19195 > 58514-1 (TE Connectivity)PROCRIMP TL W/DIE MR18-26 PDF资料下载
参数资料
| 型号： | 58514-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/6页 |
| 文件大小： | 0K |
| 描述： | PROCRIMP TL W/DIE MR18-26 |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, MR |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，18-26 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 242 (CN2011-ZH PDF) |
| 配用： | 350666-1-ND - CONN SOCKET 18-26AWG CRIMP TIN A25442-ND - CONN PIN GRND 18-26AWG TIN CRIMP A25445-ND - CONN SOCKET 24-26AWG GOLD CRIMP A25441-ND - CONN SOCKET 24-26AWG TIN CRIMP A25444-ND - CONN PIN 24-26AWG GOLD CRIMP A25446-ND - CONN PIN 18-26AWG GOLD CRIMP A25440-ND - CONN PIN 24-26AWG TIN CRIMP A14196-ND - CONN SOCKET 18-26AWG GOLD CRIMP A14197-ND - CONN SOCKET 18-26AWG TIN CRIMP A14198-ND - CONN PIN 18-26AWG GOLD CRIMP 更多... |
| 其它名称： | 58514-1-ND A25448 |
408-9973
Nut
Chamfer
Wire Crimper
Offset
Wire Anvil
Insulation
Crimper
Locator
Assembly
Tool Frame
Die Retaining
Pins
Insulation
Anvil
Chamfer
Die Retaining
Screws
Die Retaining
Screws
Figure 2
3. INSTALLATION AND REMOVAL OF DIE SET AND
LOCATOR ASSEMBLY (Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
anvils and crimpers in place, then tighten both die
retaining screws.
10. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
11. Place the nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the locator to slide up
and down.
12. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the four
die retaining pins, and slide the anvils and crimpers
out of the tool jaws.
4. CONTACT SUPPORT ADJUSTMENT (Figure 3)
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
NOTE
The contact support is preset prior to shipment, but
minor adjustment may be necessary.
NOTE
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure that
the anvils and crimpers align properly.
9. Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold the
Rev C
i
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. .If adjustment is required, loosen the screw that
holds the contact support onto the locator assembly.
The ratchet has detents that create audible clicks
as the tool handles are closed.
i
2 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 90870-1 | TOOL CRIMP .062 AWG 30 W/DIE |
| 90871-1 | PROCRIMPER III W/DIE 14-20AWG |
| 90869-1 | TOOL CRIMP .062 AWG 24 W/DIE |
| 210-5MSD | SWITCH RAISED ACTUATOR 5 SEC |
| 210-5LPSD | SWITCH SPST 5 SEC STRAIGHT TERM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5851411 | 制造商:Dialight 功能描述:LED MIDGET FLANGE BASE 6V YELLOW 制造商:Dialight 功能描述:LED Uni-Color Yellow 585nm 2-Pin |
| 585-1411 | 功能描述:LED替换灯-基于LED YELLOW 6V MULTI-CHIP RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5851411F | 制造商:Dialight 功能描述:LED MIDGET FLANGE BASE 6V YELLOW |
| 585-1411F | 功能描述:LED替换灯-基于LED MDGT FLNG BASED LED YEL 6V RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5851413 | 制造商:Dialight 功能描述:LED Uni-Color Yellow 585nm 2-Pin |
发布紧急采购，3分钟左右您将得到回复。