- 您现在的位置：买卖IC网 > Datasheet目录601 > 58529-2 (TE Connectivity)TOOL DIE SET CRIMP TERMINAL Datasheet资料下载
参数资料
| 型号： | 58529-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/6页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE SET CRIMP TERMINAL |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, AMPSEAL |
| 压接或电缆尺寸： | 16-20 AWG |
| 压接手柄： | A9996-ND |
| 连接器类型： | 压接端子 |
| 相关产品： | 679304-1-ND - TOOL PNEUMATIC HEAD ASSEMBLY A97885-ND - TOOL HAND CRIMPING SDE PEW 12 A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | Q1402659 |
408- 9999
CAUTION
!
Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do
NOT attempt to crimp an improperly positioned
contact.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimp section listed.
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire into contact insulation and
wire barrels until it is butted against the wire stop,
as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figure 5)
NOTE
i
The crimped contact may stick in the crimping
area, but the contact can be easily removed by
pushing downward on the top of the locator (see
Figure 3).
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
7. Check the contact’s crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, RATCHET ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp--height comparator. TE does
not manufacture or market crimp--height comparators.
Detailed information on obtaining and using
crimp--height comparators can be found in instruction
sheet 408--7424.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher--numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower--numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
Screwdriver
Position Point
on Center of
Wire Barrel
Opposite
Seam
Modified Anvil
Wire Size
AWG (Max)
18
16
Crimp Section
(Wire Size Marking)
20--18
16
“A”
Crimp Height
Dimension A
1.22 ? .05
[.048 ? .002]
1.41 ? .05
[.056 ? .002]
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
4 of 6
Figure 4
Figure 5
Rev C
相关PDF资料 |
PDF描述 |
|---|---|
| 58532-1 | TOOL FIBER OPTIC PRO CRIMPER III |
| 58541-2 | TOOL DIE FOR PRO-CRIMPER II |
| 58545-1 | DIE SET UNINSULATED TERMINALS |
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5852-9SL005 | 制造商:Alpha Wire Company 功能描述:Grey hook-up equipment wire,28awg |
| 5852-C | 制造商:Johanson Manufacturing 功能描述:VARIABLE CAPACITOR |
| 58-5-2CE | 制造商:OENINDIA 制造商全称:OEN India Limited 功能描述:MINIATURE POWER RELAY |
| 58-5-2CNIL | 制造商:OENINDIA 制造商全称:OEN India Limited 功能描述:MINIATURE POWER RELAY |
| 5852-GR001 | 制造商:Alpha Wire 功能描述: |
发布紧急采购，3分钟左右您将得到回复。