- 您现在的位置：买卖IC网 > Datasheet目录601 > 58532-1 (TE Connectivity)TOOL FIBER OPTIC PRO CRIMPER III Datasheet资料下载
参数资料
| 型号： | 58532-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL FIBER OPTIC PRO CRIMPER III |
| 产品培训模块： | LightCrimp PLUS SC Connector 900um Termination Installation Guide |
| 标准包装： | 25 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手持压接器 - 无模具 |
| 适用于相关产品： | 因模具套件而异 |
| 特点： | 侧面插入，棘齿 |
| 配用： | A20217-ND - DIE SET F/OPTIC FSD USE W/A9996 |
| 其它名称： | A36400 |
5. To remove the die assembly, close the tool
handles until the ratchet releases, and allow the
Select the desired die assembly, remove the die
retention screws from the tool jaws, and proceed as
follows:
1. Place the upper die in the stationary jaw of the
tool frame.
handles to open fully. Loosen and remove the die
retention screws and slide the dies out of the tool
jaws.
1. Install the wire and insulation anvil dies, with the
chamfers facing the front of the tool, and with the
die markings facing outward, into the movable jaw
of the frame assembly.
2. Insert the die retaining pins and the short die
retention screw. Do not tighten the screw
completely.
3. Install the wire and insulation crimper dies, with
the chamfers facing the front of the tool, and with
the die markings facing outward, into the stationary
jaw of the frame assembly.
4. Insert the die retaining pins and the long die
retention screw. Do not tighten the screw
completely.
Figure 2
2. Insert a die retention screw through the jaw and
die and tighten the screw so that the die is held in
place, but do not tighten the screw completely at
this point.
3. Place the lower die in the moving jaw of the tool
frame. Install a die retention screw through the jaw
and die and tighten the screw so that the die is
held in place, but do not tighten the screw
Figure 3
completely at this point.
5. Slowly close the tool handles, allowing the dies
to mate and/or align. Continue closing the tool
handles until the ratchet makes the fourth “click,”
then tighten both die retention screws until snug.
6. Install the locator assembly and tighten the hex
4. Slowly close the tool handles, allowing the dies
to mate and/or align. Continue closing the tool
handles until the ratchet makes the fourth “click,”
then tighten both die retention screws until snug.
nut.
7. Reverse the procedure to remove the die
assembly.
相关PDF资料 |
PDF描述 |
|---|---|
| 58541-2 | TOOL DIE FOR PRO-CRIMPER II |
| 58545-1 | DIE SET UNINSULATED TERMINALS |
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5853211 | 制造商:Dialight 功能描述:LED Uni-Color Red 660nm 2-Pin |
| 585-3211 | 功能描述:LED替换灯-基于LED BI-PIN BASED LED U RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5853213 | 制造商:Dialight 功能描述:LED Uni-Color Red 660nm 2-Pin |
| 585-3213 | 功能描述:LED替换灯-基于LED BI-PIN BASED LED U RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5853215 | 制造商:Dialight 功能描述:LED Uni-Color Red 660nm 2-Pin |
发布紧急采购，3分钟左右您将得到回复。