- 您现在的位置：买卖IC网 > Datasheet目录601 > 58541-2 (TE Connectivity)TOOL DIE FOR PRO-CRIMPER II Datasheet资料下载
参数资料
| 型号： | 58541-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/4页 |
| 文件大小： | 0K |
| 描述： | TOOL DIE FOR PRO-CRIMPER II |
| 标准包装： | 1 |
| 系列： | * |
408-4051
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
Screwdriver
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 6,
CRIMP HEIGHT ADJUSTMENT.
Ratchet
Adjustment
Wheel
Lockscrew
(Typ)
WIRE SIZE
AWG (MAX)
CRIMP SECTION
(WIRE SIZE
MARKING)
CRIMP HEIGHT
DIM. (A) AND
TOLERANCE (±)
8. VISUAL INSPECTION
Figure 5
20
14
24-20
18-16-14
1.09 ±0.051
[.043 ±.002]
1.60 ±0.051
[.063 ±.002]
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimp sections for flattened,
chipped, worn, or broken areas. If damage or
abnormal wear is evident, the tool must be replaced.
Figure 4
6. CRIMP HEIGHT ADJUSTMENT (Figure 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel from
the locator side of the tool.
3. Observe the ratchet adjustment wheel. If a tighter
crimp is required, rotate the adjustment wheel
COUNTERCLOCKWISE to a higher-numbered
setting. If a looser crimp is required, rotate the
adjustment wheel CLOCKWISE to a lower-
numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, replace and
secure the lockscrew. If the dimension is
unacceptable, continue to adjust the ratchet, and
again measure a sample crimp.
7. MAINTENANCE
Ensure that the tool and dies are clean by wiping them
with a clean, soft cloth. Remove any debris with a
clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in the
crimping dies, and store in a clean, dry area.
Rev D
See Section 9, REPLACEMENT.
9. REPLACEMENT
Customer-replaceable parts are shown in Figure 1.
Available separately, PRO-CRIMPER III Hand
Crimping Tool Repair Kit 679221-1 includes a
replacement nut and a variety of pins, rings, screws,
and springs. If the dies are damaged or worn
excessively, they must be replaced. Order the repair
kit and replaceable parts through your TE
Representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 1-717-986-7605, or
write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
10. REVISION SUMMARY
? Updated document to corporate requirements
? Changed wire size marking in table in Figure 4
4 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 58545-1 | DIE SET UNINSULATED TERMINALS |
| 58558-1 | CONSUMER BNC TOOL RG 58/59 |
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5854121 | 制造商:Dialight 功能描述:LED Uni-Color Red 630nm 2-Pin |
| 585-4121 | 功能描述:LED替换灯-基于LED BAYONET RED 6V NON-P RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5854123 | 制造商:Dialight 功能描述:LED Uni-Color Red 630nm 2-Pin |
| 585-4123 | 功能描述:LED替换灯-基于LED RED 14V MULTI-CHIP RoHS:否 制造商:Chicago Miniature 照明颜色:Red 光强度: 电压额定值:115 V 封装: |
| 5854125 | 制造商:Dialight 功能描述:LED Uni-Color Red 630nm 2-Pin |
发布紧急采购，3分钟左右您将得到回复。