参数资料
型号: 5962-88565012A
厂商: ANALOG DEVICES INC
元件分类: 运算放大器
英文描述: QUAD OP-AMP, 400 uV OFFSET-MAX, 6 MHz BAND WIDTH, CQCC20
封装: CERAMIC, LCC-20
文件页数: 2/16页
文件大小: 680K
代理商: 5962-88565012A
REV. A
OP470
–10–
Figure 6 shows peak-to-peak noise versus source resistance over
the 0.1 Hz to 10 Hz range. Once again, at low values of RS, the
voltage noise of the OP470 is the major contributor to peak-to-peak
noise with current noise the major contributor as RS increases.
The crossover point between the OP470 and the OP400 for
peak-to-peak noise is at RS= 17 k
W.
The OP471 is a higher speed version of the OP470, with a slew
rate of 8 V/
ms. Noise of the OP471 is only slightly higher than
the OP470. Like the OP470, the OP471 is unity-gain stable.
RS – SOURCE RESISTANCE –
1000
10
100
100k
PEAK-T
O-PEAK
NOISE
nV/
Hz
100
10k
1k
OP11
OP400
OP471
OP470
RESISTOR
NOISE ONLY
Figure 6. Peak-To-Peak Noise (0.1 Hz to 10 Hz) vs. Source
Resistance (Includes Resistor Noise)
For reference, typical source resistances of some signal sources
are listed in Table I.
R1
5
R3
1.24k
OP470
DUT
R2
5
R5
909
OP27E
R4
200
C1
2 F
R6
600k
R9
306k
OP15E
R8
10k
D1
1N4148
D2
1N4148
C2
0.032 F
R10
65.4k
R11
65.4k
C3
0.22 F
OP15E
C4
0.22 F
R13
5.9k
R12
10k
R14
4.99k
C5
1 F
eOUT
GAIN = 50,000
VS = 5V
Figure 7. Peak-To-Peak Voltage Noise Test Circuit (0.1 Hz to 10 Hz)
TABLE I.
Device
Source
Impedance
Comments
Strain gauge
<500
W
Typically used in
low frequency applications.
Magnetic
<1500
W
Low IB very important to reduce
tapehead
self-magnetization problems
when direct coupling is used.
OP470 IB can be neglected.
Magnetic
<1500
W
Similar need for low IB in direct
phonograph
coupled applications. OP470
cartridges
will not introduce any self-
magnetization problem.
Linear variable <1500
W
Used in rugged servo-feedback
differential
applications. Bandwidth of
transformer
interest is 400 Hz to 5 kHz.
For further information regarding noise calculations, see “Minimization of Noise
in Op Amp Applications,” Application Note AN-15.
NOISE MEASUREMENTS—
PEAK-TO-PEAK VOLTAGE NOISE
The circuit of Figure 7 is a test setup for measuring peak-to-peak
voltage noise. To measure the 200 nV peak-to-peak noise speci-
fication of the OP470 in the 0.1 Hz to 10 Hz range, the following
precautions must be observed:
1. The device must be warmed up for at least five minutes. As
shown in the warm-up drift curve, the offset voltage typi-
cally changes 5
mV due to increasing chip temperature after
power-up. In the 10-second measurement interval, these
temperature-induced effects can exceed tens of nanovolts.
2. For similar reasons, the device must be well-shielded from
air currents. Shielding also minimizes thermocouple effects.
3. Sudden motion in the vicinity of the device can also “feedthrough”
to increase the observed noise.
相关PDF资料
PDF描述
5962-88565013A QUAD OP-AMP, 600 uV OFFSET-MAX, 6 MHz BAND WIDTH, CQCC28
5962-8856501CA QUAD OP-AMP, 400 uV OFFSET-MAX, 6 MHz BAND WIDTH, CDIP14
5962-88565013C QUAD OP-AMP, 600 uV OFFSET-MAX, 6 MHz BAND WIDTH, CQCC28
5962-88565013B QUAD OP-AMP, 600 uV OFFSET-MAX, 6 MHz BAND WIDTH, CQCC28
5962-88565013B QUAD OP-AMP, 600 uV OFFSET-MAX, 6 MHz BAND WIDTH, CQCC28
相关代理商/技术参数
参数描述
5962-88565013A 制造商:Rochester Electronics LLC 功能描述:QUAD LOW-NOISE OPAMP IC - Bulk
5962-8856501CA 功能描述:仪表放大器 QUAD LOW-NOISE OP AMP IC RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比(最小值):88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk
5962-8856501V2A 制造商:Analog Devices 功能描述:OP AMP, QUAD, LOW-NOISE - Rail/Tube
5962-8856501VCA 制造商:Analog Devices 功能描述:OP AMP QUAD GP 18V 14CDIP - Rail/Tube
5962-88565022A 功能描述:高速运算放大器 QUAD HI-SPEED LO-NOISE IC RoHS:否 制造商:Texas Instruments 通道数量:1 电压增益 dB:116 dB 输入补偿电压:0.5 mV 转换速度:55 V/us 工作电源电压:36 V 电源电流:7.5 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube 产品: