- 您现在的位置：买卖IC网 > PDF目录157280 > 5962-9855202QXC 32-BIT, 16 MHz, RISC MICROCONTROLLER, CPGA144 PDF资料下载
参数资料
| 型号： | 5962-9855202QXC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, 16 MHz, RISC MICROCONTROLLER, CPGA144 |
| 封装： | CERAMIC, PGA-144 |
| 文件页数： | 20/64页 |
| 文件大小： | 1464K |
| 代理商： | 5962-9855202QXC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
27
The interrupt architecture allows for the disabling and masking
of certain interrupts. Output Register Instruction OTR
Rd,ENBL and OTR Rd,DSBL control the disable and enable
of interrupts. The content of the Rd register is a “don’t care”
for these commands. Status Register bit 9 reflects the state of
interrupts (i.e., enabled or disabled). The Mask Register
provides the ability to mask the service of user selected
interrupts. Interrupts awaiting service are reflected in the PI
Register. Execution of Input Register and Output Register
Instructions INR Rd,PI, OTR Rd,PI and OTR Rd,RPI read,
write, and clear the PI Register. To latch an interrupt into the
PI Register the corresponding bit must be a logic zero before
the event occurs. An integral part of interrupt service should
include the clearing of the appropriate bit in the PI Register.
Section 2.2.1 shows an example of clearing the PI register.
6.1.1 Interrupt Status
The architecture of the UT69R000 allows for the disabling and
masking of interrupts. If the software cannot support interrupt
service the software can disable (i.e., not recognize) interrupts.
The disable feature will prevent the servicing of all interrupts
with the exception of power fail (PFAIL) and software interrupt
(USR2). The UT69R000 will log these interrupts into the PI
Register but does not alter program flow to the interrupt vector.
Re-enabling interrupts with a non-zero PI Register will result
in the UT69R000 vectoring to the highest priority interrupt. To
prevent the service of these interrupt clear the PI Register
before re-enabling interrupts.
The mask feature allows the software to select particular
interrupts for service while masking others. The selection of
interrupts, via the mask feature, for service is controlled
through the MK Register. Input Register and Output Register
Instructions INR Rd,MK and OTR Rd,MK read and write the
MK register. The mask feature prevents the servicing of all
interrupts with the exception of PFAIL and USR2. Similiar to
the disable feature, unmasking and interrupt with a non-zero
PI Register results in the vectoring to the appropriate interrupt
vector. Writing a logical zero into a Mask Register bit location
will prevent the recognition of the specific interrupt (i.e.,
mask). To un-mask all interrupts write FFFF (hex) to the MK
register.
To enable the UT69R000 interrupts architecture the software
program enables interrupts by executing instruction OTR
Rd,ENBL, followed by a write to the Mask Register, OTR
Rd,MK. Interrupts are enabled and disabled on the falling edge
of internal clock cycle CK1 (rising edge of CK2).
6.1.2 Interrupt Processing and Vectors
The occurrence of an enabled and non-masked interrupts
results in the altering of program flow. Interrupt processing
begins by saving the present Instruction Counter Register (IC)
in the Instruction Counter Save Register (ICS) followed by
automatic disabling of all interrupts (Status Register Bit 9
equals logic 0). The UT69R000 then loads the designated
interrupt vector location into the Instruction Counter. The
UT69R000 begins interrupt service by executing the code
residing at the interrupt vector location.
Interrupt vectors reside from memory location 400 (hex) to 43C
(hex). Each interrupt is assigned a vector with four memory
locations (see table 2). These four memory locations allow for
storage of the Instruction Counter Save Register (ICS) and a
jump (JC), branch (BR), or call (CALL) to the interrupt service
routine. An example is shown below.
ISR0_INT0:
408 (hex) INR xR0, ICS
409 (hex) CALL xR18, ISR0
40A (hex) ISR0
40B (hex) NOP
Table 2. Interrupt Instruction Counter
Load Location
INTERRUPT
NUMBER
LOCATION
(HEX)
MASK-
(Y/N)
CAN USER
DISABLE
(Y/N)
ABLE
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15*
0400
0404
0408
040C
0410
0414
0418
041C
0420
0424
0428
042C
0430
0434
0438
043C
N
Y
N
Y
N
Y
N
Y
* See note on page 11.
相关PDF资料 |
PDF描述 |
|---|---|
| 5962-9855202QXX | 32-BIT, 16 MHz, RISC MICROCONTROLLER, CPGA144 |
| 5962F9855202QXA | 32-BIT, 16 MHz, RISC MICROCONTROLLER, CPGA144 |
| 5962G9855201QXX | 32-BIT, 12 MHz, RISC MICROCONTROLLER, CPGA144 |
| 5962G9855202VXA | 32-BIT, 16 MHz, RISC MICROCONTROLLER, CPGA144 |
| 5962G9855202VXX | 32-BIT, 16 MHz, RISC MICROCONTROLLER, CPGA144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 5962-9855501VPA | 功能描述:计时器和支持产品 QML Class V Prec Timer RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| 59629856401QEA | 制造商:TI 功能描述:SNJ5447AJ |
| 5962-9856401QEA | 制造商:Texas Instruments 功能描述:Decoder/Driver Single 4-to-7 16-Pin CDIP Tube |
| 5962-9858401QFA | 功能描述:LVDS 接口集成电路 RoHS:否 制造商:Texas Instruments 激励器数量:4 接收机数量:4 数据速率:155.5 Mbps 工作电源电压:5 V 最大功率耗散:1025 mW 最大工作温度:+ 85 C 封装 / 箱体:SOIC-16 Narrow 封装:Reel |
| 5962-9858501QFA | 功能描述:总线接收器 RoHS:否 制造商:Texas Instruments 接收机数量:4 接收机信号类型:Differential 接口类型:EIA/TIA-422-B, V.11 工作电源电压:3.3 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:TSSOP-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。