ISL70001SRH
8
FN6947.1
May 23, 2011
POWER-ON RESET
POR Select (PORSEL)
Input High Threshold
1.4
V
Input Low Threshold
1.2
V
POR Select (PORSEL) Input Leakage
Current
VIN = 5.5V, PORSEL = GND or VIN
0A
VIN POR
Rising Threshold, PORSEL = VIN
4.25
V
Hysteresis, PORSEL = VIN
325
mV
Rising Threshold, PORSEL = GND
2.8
V
Hysteresis, PORSEL = GND
175
mV
Enable (EN) Input Voltage
Rising/Falling Threshold
0.6
V
Enable (EN) Input Leakage Current
VIN = 5.5V, EN = GND or VIN
0A
Enable (EN) Sink Current
EN = 0.3V
11
A
SOFT-START
Soft-Start Source Current
SS = GND
23
A
Soft-Start Discharge ON-Resistance
2.2
Ω
Soft-Start Discharge Time
256
Clock Cycles
POWER-GOOD SIGNAL
Rising Threshold
VFB as a % of VREF, Test Mode
111
%
Rising Hysteresis
VFB as a % of VREF, Test Mode
3.5
%
Falling Threshold
VFB as a % of VREF, Test Mode
89
%
Falling Hysteresis
VFB as a % of VREF, Test Mode
3.5
%
Power-Good Drive
VIN = 3V, PGOOD = 0.4V, EN = GND
8.2
mA
Power-Good Leakage
VIN = PGOOD = 5.5V
0.001
A
PROTECTION FEATURES
Undervoltage Monitor
Undervoltage Trip Threshold
VIN = 3V, VFB as a % of VREF, Test mode
75
%
Undervoltage Recovery Threshold
VIN = 3V, VFB as a % of VREF, Test mode
88
%
Overcurrent Monitor
Overcurrent Trip Level
LX4 Power Block, Test Mode, (Note
7)1.9
A
Overcurrent or Short-Circuit Duty-Cycle
VIN = 3V, SS interval = 200s, Test Mode, Fault
interval divided by hiccup interval
0.8
%
NOTES:
3. Typical values shown are not guaranteed. Guaranteed min/max values are provided in the SMD.
4. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
5. Limits do not include tolerance of external feedback resistors. The 0A to 6A output current range may be reduced by Minimum LXx On Time and
Minimum LXx Off Time specifications.
6. Limits established by characterization or analysis and are not production tested.
7. During an output short-circuit, peak current through the power block(s) can continue to build beyond the overcurrent trip level by up to 3A. With all six
power blocks connected, peak current through the power blocks and output inductor could reach (6 x 2.5A) + 3A = 18A. The output inductor must
support this peak current without saturating.
Electrical Specifications Unless otherwise noted, VIN = AVDD = DVDD = PVINx = EN = M/S = 3V or 5.5V; GND = AGND = DGND =
PGNDx = TDI = TDO = ZAP = 0V; FB = 0.65V; PORSEL = VIN for 4.5V ≤ VIN ≤ 5.5V and GND for VIN < 4.5V, SYNC = LXx = Open Circuit; PGOOD is
pulled up to VIN with a 1k resistor; REF is bypassed to GND with a 220nF capacitor; SS is bypassed to GND with a 100nF capacitor; IOUT = 0A;
TA = TJ = +25°C. (Note 3) (Continued)
PARAMETER
TEST CONDITIONS
MIN
(Note 4)
TYP
MAX
(Note 4)
UNITS