- 您现在的位置：买卖IC网 > PDF目录18547 > 59826-1 (TE Connectivity)TOOL TETRA-CRIMP DIE 22-18AWG PDF资料下载
参数资料
| 型号： | 59826-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/7页 |
| 文件大小： | 0K |
| 描述： | TOOL TETRA-CRIMP DIE 22-18AWG |
| 标准包装： | 1 |
| 系列： | * |
408- 2822
Chipped Edge
Pitted
Figure 4
A. Wire Barrel Crimp Die Closure (Figure 7A)
1. Assemble dies so that wire barrel crimp dies are
bottomed but not under pressure.
2. With wire barrel crimp dies bottomed, inspect
the wire barrel crimp die closure using the proper
plug gage. Hold gage in straight alignment with the
die closure and carefully insert, without forcing, the
GO element. The GO element must pass
completely through the wire barrel crimp die
closure.
3. Try to insert the NO--GO element. The NO--GO
element may enter partially, but must not pass
completely through the wire barrel crimp die
closure.
B. Insulation Crimp Die Closure (Figure 7B)
1. With the wire barrel crimp dies bottomed and
not under pressure, adjust the dies to meet the
“gage dimension” as shown in Figure 7B.
2. Inspect the insulation crimp die closure using
the proper plug gage in the same manner as steps
6.5.A. (2) and (3).
If both the wire barrel and insulation crimp die
closures meet the plug gage conditions, the dies are
considered to be correct and should be lubricated with
a THIN coat of any good SAE No. 20 motor oil. If not,
the dies must be repaired before returning them to
service (See Paragraph 7, DIE REPLACEMENT AND
REPAIR).
Suggested Plug Gage Design - Wire Barrel
Die Closure
Configuration
“C” Dim.
GO Dim.
“B”
NO-- GO Dim.
“B”
“C” Dim.
“A” Dim.
Break Edges
0.51 [.020] x 45 ? (Typ)
25.4 [1.00] Min. (Typ)
DIE SET
DIE CLOSURE DIM’S “A” {
GO NO-- GO
GAGE ELEMENT } DIM’S “B”
GO NO-- GO
“C” DIM
59826--1
59827--1
59828--1
1.98 [.078]
2.33 [.092]
3.25 [.128]
2.18 [.086]
2.54 [.100]
3.45 [.136]
1.98--1.99 [.0780--.0783]
2.33--2.34 [.0920--.0923]
3.25--3.26 [.1280--.1283]
2.18--2.19 [.0859--.0860]
2.53--2.54 [.0999--.1000]
3.45--3.46 [.1359--.1360]
4.49 [.185]
5.33 [.210]
6.85 [.270]
{ Die closure dimensions apply when wire barrel crimp dies are bottomed but not under pressure.
} Material -- Tool Steel
Figure 5
Rev B
5 of 7
相关PDF资料 |
PDF描述 |
|---|---|
| NTB4302 | MOSFET N-CH 30V 74A D2PAK |
| NTB35N15G | MOSFET N-CH 150V 37A D2PAK |
| NTB30N20G | MOSFET N-CH 200V 30A D2PAK |
| SRF0504-402Y | INDUCTOR COMMON MODE 2.8UH 0.2A |
| 46-1-5-50-07-EW | SWITCH PUSH SPDT 0.25A 115V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 598261-1 | 制造商:TE CONNECTIVITY 功能描述:TBC PIN ASSY 4 ROW 140 PO TBC PIN ASSY 4 ROW 1 |
| 59826-2 | 功能描述:折皱器 TIE BAR SERIES 50 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 598262-1 | 制造商:TE Connectivity 功能描述:TBC PIN ASSY 4 ROW 120 POS - Rail/Tube |
| 59826-3 | 功能描述:冲压机与冲模 TETRA-CRIMP DIE 22-16 PIDG SP RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5982-6CC | 制造商:Carlisle Interconnect Components 功能描述:RF COAXIAL PANEL MOUNT CONNECTOR |
发布紧急采购，3分钟左右您将得到回复。