参数资料
| 型号： | 66164 |
| 厂商： | Desco |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | VINYL DARKBLU 2LAYER .060X24X36" |
| 其它有关文件： | Mat Selection Chart |
| 标准包装： | 1 |
| 系列： | Statfree B2™ |
| 垫子类型： | 桌子，工作台 |
| 形状： | 矩形 |
| 长度： | 3'（0.91m） |
| 宽： | 2'（0.61m） |
| 厚度： | 0.06" (1.52mm) |
| 颜色： | 深蓝色 |
| 材质： | 乙烯基 |
| 特点： | 耗散 |
| 包括： | 接地软线，接地卡扣套件 |
| 其它名称： | 16-1121 |
TB-2000 March 2012 Page 1 of 4
Installation and
Maintenance of ESD Mats
Introduction
The purpose of an ESD worksurface is to aid in the prevention
of damage to ESD sensitive components and assemblies from
electrostatic discharge. An ESD worksurface provides protection in
the following two ways:
1. Providing an antistatic worksurface area that will limit static
electricity generation.
2. Removing the charge from a conductive object placed on the
worksurface.
A dissipative worksurface having a surface resistance of at
least 1 x 10E6, but less than 1 x 10E9 ohms is recommended
by worksurface standard ANSI/ESD S4.1. Dissipative materials
minimize the generation of static charges, and will dissipate a
charge slow enough so that a spark will not occur. Dissipative
materials are usually the preferred choice for bench top
worksurfaces.
Conductive materials are the quickest to remove a charge,
but they can also cause damage by discharging too rapidly.
Conductive materials are usually used as floor mats, which is
defined by ANSI/ESD S7.1 as less than 1 x 10E6 ohms.
General Grounding Guidelines
1. ANSI/ESD S20.20 requires that all conductors in an ESD
protected area, including personnel, must be grounded.
2. The ESD ground must be tied directly to and at the same
potential as the building or “green wire” equipment ground.
3. Per ANSI/ESD S20.20, the ESD control program can in no
way replace or supercede any requirements for personnel
safety. Ground fault circuit interrupters (GFCI) and other safety
protection should be considered wherever personnel might
come into contact with electrical sources.
4. All electrical outlets should be verified for proper wiring
configuration, resistance or impedance and GFCI function when
the mat is installed and periodically thereafter.
Common Point Grounds
A common point ground is defined by the grounding standard
ANSI/ESD S6.1, as:
1. A grounded device where two or more conductors are bonded.
2. A system or method for connecting two or more grounding
conductors to the same electrical potential.
Examples of common point grounds with ground cords are
illustrated below.
Figure 2. Other ground cords.
Figure 3. 09814 with screw allows ground cord to be bolted to mat
to keep cord from disconnecting.
Common point grounds are designed to provide ground for
worksurface mats, wrist straps, and other items.
NOTE: DO NOT DAISY CHAIN. Because of the high resistances
inherent to many types of protective surfaces, daisy chaining of
these materials can severely limit their ability to properly dissipate
and protect against static charges.
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way
, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
TECHNICAL BULLETIN TB-2000
Made in the
United States of America
2012 DESCO INDUSTRIES INC.
Employee Owned
Figure 1. Typical common point grounds.
COMMON POINT GROUND
Per ANSI/ESD S6.1, Grounding section 4.1.1 “Every element to be
grounded at an ESD protected station shall be connected to the
same common point ground.”
ESD Handbook ESD TR20.20 section 5.1.3 Basic Grounding
Requirements “The first step in ensuring that everything in an
EPA is at the same electrical potential is to ground all conductive
components of the work area (worksurfaces, people, equipment,
etc.) to the same electrical ground point. This point is called the
common point ground. The next step in completing the ground
circuit is to connect the common point ground to the equipment
ground (third wire, green).”
WRONG!
RIGHT
Figure 4. ESD mats should never be grounded in series, that is
daisy chained.
相关PDF资料 |
PDF描述 |
|---|---|
| FODM3062R2 | OPTOCOUPLER TRIAC 600V 4-SMD |
| 433201-20-0 | TERM BARRIER 20CIRC 1 ROW .4375 |
| 433101-20-0 | TERM BARRIER 20CIRC 1 ROW .4375 |
| 66040 | MAT KIT DUAL RUBBER BLUE 24X36" |
| 430113-22-0 | TERM BARRIER 22CIRC 1 ROW .4375 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 66-164 | 功能描述:SCRDR PHLP RND #4 制造商:apex tool group 系列:* 零件状态:在售 标准包装:1 |
| 66164-001 | 制造商:MII 制造商全称:MII 功能描述:SINGLE CHANNEL LINEAR OPTOCOUPLER Electrically Similar to 3C92C |
| 66164-011 | 制造商:MII 制造商全称:MII 功能描述:SINGLE CHANNEL LINEAR OPTOCOUPLER Electrically Similar to 3C92C |
| 66164-101 | 制造商:Micropac Industries Inc 功能描述:Optocoupler DC-IN 1-CH Transistor DC-OUT |
| 66165 | 制造商:Desco Industries Inc 功能描述:Tray Liner; ESD; Dual Layer; Vinyl; 16 In.; 24 In.; 0.060 In.; Dark Blue |
发布紧急采购，3分钟左右您将得到回复。