参数资料
型号: 6N139#360
元件分类: 光电耦合器
英文描述: 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER
封装: 0.300 INCH, SURFACE MOUNT, DIP-8
文件页数: 4/14页
文件大小: 302K
代理商: 6N139#360
12
Notes:
1. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I
O, to the forward LED input current, IF, times 100%.
2. Pin 7 Open.
3. Device considered a two-terminal device. Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
4. Use of a resistor between pin 5 and 7 will decrease gain and delay time. Significant reduction in overall gain can occur when using resistor values
below 47 k
Ω. For more information, please contact your local Avago Components representative.
5. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt of the common mode pulse, VCM, to assure
that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable
(negative) dVCM/dt of the common mode pulse, V
CM, to assure that the output will remain in a Logic Low state (i.e., VO < 0.8 V).
6. In applications where dV/dt may exceed 50,000 V/s (such as static discharge) a series resistor, RCC, should be included to protect the
detector IC from destructively high surge currents. The recommended value is RCC = 220
Ω.
7. Use of a 0.1
F bypass capacitor connected between pins 8 and 5 adjacent to the device is recommended.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage 4500 V rms for 1 second (leakage detection
current limit, II-O < 5
A). This test is performed before the 100% production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Char-
acteristics Table, if applicable.
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage detection
current limit, II-O < 5
A). This test is performed before the 100% production test for partial discharge (method b) shown in the IEC/EN/DIN EN
60747-5-2 Insulation Related Characteristics Table, if applicable.
Package Characteristics
Parameter
Sym.
Min.
Typ.**
Max.
Units
Test Conditions
Fig.
Note
Input-Output Momentary
VISO
3750
V rms
RH < 50%, t = 1 min.,
3, 8
Withstand Voltage
TA = 25°C
Option 020
5000
3, 9
HCNW139
HCNW138
Resistance (Input-Output)
RI-O
1012
Ω
VI-O = 500 Vdc
3
RH < 45%
Capacitance (Input-Output)
CI-O
0.6
pF
f = 1 MHz
3
**All typicals at T
A = 25°C, unless otherwise noted.
TheInput-OutputMomentaryWithstandVoltageisadielectricvoltageratingthatshouldnotbeinterpretedasaninput-outputcontinuousvoltagerating.
For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level safety
specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.”
相关PDF资料
PDF描述
61-236/LK2C-B28324E6GB2/ET T-1 SINGLE COLOR LED, WARM WHITE, 3 mm
61-236/LK2C-B28326D6EB2/ET T-1 SINGLE COLOR LED, WARM WHITE, 3 mm
61-236/LK2C-B2832AE4FB2/ET T-1 SINGLE COLOR LED, WARM WHITE, 3 mm
61-236/LK2C-B50634D2GB2/ET T-1 SINGLE COLOR LED, COOL WHITE, 3 mm
61-236/MK2C-B28322E4EB2/ET T-1 SINGLE COLOR LED, WARM WHITE, 3 mm
相关代理商/技术参数
参数描述
6N139-500E 功能描述:高速光耦合器 100 KBd 2500Vrms RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
6N139-50ME 制造商:Avago Technologies 功能描述:6N139-50ME^AVAGO
6N139-520E 功能描述:高速光耦合器 100 KBd 5000Vrms RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
6N139-560E 功能描述:高速光耦合器 100 KBd 2500Vrms RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
6N139-L 制造商:Lite-On 功能描述:Optocoupler Darlington Output, DIP8 制造商:Lite-On Electronics 功能描述:6N139-L^LITEON