- 您现在的位置：买卖IC网 > Datasheet目录299 > 71M6515H-IGT/F (Maxim Integrated)IC ENERGY METER AFE 3PH 64-LQFP Datasheet资料下载
参数资料
| 型号： | 71M6515H-IGT/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 18/60页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER AFE 3PH 64-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 160 |
| 系列： | Single Converter Technology® |
| 测量误差： | 0.1% |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
71M6515H
A Maxim Integrated Products Brand
Energy Meter IC
DATA SHEET
JULY 2011
Internal data is pulsed out during the accumulation interval immediately following its accumulation interval. Post-processed
values are pulsed out one accumulation interval after that.
The pulse generator output rate depends on its input value, WRATE , PULSE_SLOW , and PULSE_FAST . Additionally, its
maximum pulse width (negative going pulse) is controlled by PULSEWIDTH . High frequency pulses will have 50% duty cycle
until their rate slows enough that their pulse width is limited by PULSEWIDTH .
In internal and post-processed modes, the pulse rate, expressed as Kh (Wh per pulse) is given by the formula:
Kh =
VMAX IMAX
In _ 8 ? SUM _ CYCLES ? WRATE ? X
1 . 5757 Wh / Pulse
where
VMAX is the meter voltage corresponding to an input voltage of 176mV (rms) at the VA, VB, and VC input pins ,
IMAX is the meter current corresponding to an input voltage of 176mV (rms) at the IA, IB, and IC input pins,
In_8 is the additional ADC gain (1 or 8), as controlled by the IA_X , IB_X and IC_X bits in the CONFIG register.
X is the pulse speed factor determined from Table 3.
1.5*2 =6
PULSE_SLOW
0
0
1
1 (default)
PULSE_FAST
0
1
0
1 (default)
X
2
1.5*2 6 =96
1.5*2 -4 =0.09375
1.5
Table 3: Pulse Speed Factor X
In external pulse mode, the pulse rate is given by the formula:
Rate(Hz) = WRATE * X * input * 35.82*10 -12 ,
where input is the value in registers APULSER, APULSEW. APULSE3 or APULSE4,
X is the pulse speed factor determined from Table 3.
External pulse generation can be seen as providing the raw voltage and current readings equivalent to V in *I in / LSB directly to
the pulse generator.
The maximum pulse rate is 7.56kHz for PULSEW and PULSER, and 150Hz for PULSE3 and PULSE4.
In external pulse mode, the pulse generators load their data at the beginning of each CE accumulation interval, preserving any
partially implemented pulses from the previous interval. The source of data is controlled by the entries in the PULSE_SRCS
register. PULSER_SRCS contains 8-bit entries for each pulse source, PULSEW, PULSER, PULSE3, and PULSE4. See the
register description for details.
The procedure for accurate external pulse generation controlled by the host is:
1)
2)
3)
Respond to a READY interrupt by reading the accumulated values.
Process the accumulated values.
Write the processed value(s) to APULSER, APULSEW, APULSE3, or APULSE4 . The host must write to APULSER,
APULSEW, APULSE3, and APULSE4 before the next READY interrupt for the pulse generation to be beginning in the
following accumulation interval.
Figure 8 illustrates pulse generator timing.
Regardless of the source, the pulse generators should receive new data during each accumulation interval. If this does not
occur and if the corresponding bit in the STMASK register is set, an APULSE_ERR interrupt will be issued.
The PULSEW, PULSER, PULSE3 and PULSE4 pins are suitable for driving LEDs through a current limiting resistor. The LED
should be connected so it is on when the pulse pin is low.
Page: 18 of 60
? 2005 ? 2011 Teridian Semiconductor Corporation
1.6
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6521BE-IGTR/F | IC ENERGY METER 8K FLASH 64-LQFP |
| 71M6533G-IGTR/F | IC ENERGY METER 3PH 100LQFP |
| 71M6543F-IGT/F | IC ENERGY METERING |
| 71M6545-IGT/F | IC ENERGY METERING |
| 720-10007-00300 | CBL D-SUB 9PIN FMAL-25PIN FML 3M |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6515H-IGTR | 制造商:Maxim Integrated Products 功能描述:71M6515H-IGT - T/REEL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Energy Meter IC |
| 71M6515H-IGTR/F | 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6515H-IGTW/F | 功能描述:计量片上系统 - SoC Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6515H-IGTW1 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation |
| 71M6515H-IGTWR1 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Up to 10ppmC precision ultra-stable voltage reference Digital temperature compensation |
发布紧急采购，3分钟左右您将得到回复。