参数资料
型号: 71M6521FE-IMR/F
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, QCC68
封装: LEAD FREE, LQFN-68
文件页数: 43/103页
文件大小: 1691K
代理商: 71M6521FE-IMR/F
71M6521DE/71M6521FE
Energy Meter IC
DATA SHEET
OCTOBER 2010
Page: 44 of 103
2005-2010 Teridian Semiconductor Corporation
v1.1
A Maxim Integrated Products Brand
19-5370; 10/10
Three-Wire EEPROM Interface
A 500kHz three-wire interface, using SDATA, SCK, and a DIO pin for CS is available. The interface is selected with
DIO_EEX=3. The same 2-wire EECTRL register is used, except the bits are reconfigured, as shown in Table 58. When EECTRL
is written, up to 8 bits from EEDATA are either written to the EEPROM or read from the EEPROM, depending on the values of
the EECTRL bits.
Control
Bit
Name
Read/Write
Description
7
WFR
W
Wait for Ready. If this bit is set, the trailing edge of BUSY will be delayed
until a rising edge is seen on the data line. This bit can be used during
the last byte of a Write command to cause the INT5 interrupt to occur
when the EEPROM has finished its internal write sequence. This bit is
ignored if HiZ=0.
6
BUSY
R
Asserted while serial data bus is busy. When the BUSY bit falls, an INT5
interrupt occurs.
5
HiZ
W
Indicates that the SD signal is to be floated to high impedance immedi-
ately after the last SCK rising edge.
4
RD
W
Indicates that EEDATA is to be filled with data from EEPROM.
3-0
CNT[3:0]
W
Specifies the number of clocks to be issued. Allowed values are 0
through 8. If RD=1, CNT bits of data will be read MSB first, and right
justified into the low order bits of EEDATA. If RD=0, CNT bits will be sent
MSB first to EEPROM, shifted out of EEDATA’s MSB. If CNT is zero,
SDATA will simply obey the HiZ bit.
Table 58: EECTRL bits for 3-wire interface
The timing diagrams in Figure 9 through Figure 13 describe the 3-wire EEPROM interface behavior. All commands begin when
the EECTRL register is written. Transactions start by first raising the DIO pin that is connected to CS. Multiple 8-bit or less
commands such as those shown in Figure 9 through Figure 13 are then sent via EECTRL and EEDATA. When the transaction
is finished, CS must be lowered. At the end of a Read transaction, the EEPROM will be driving SDATA, but will transition to
HiZ (high impedance) when CS falls. The firmware should then immediately issue a write command with CNT=0 and HiZ=0 to
take control of SDATA and force it to a low-Z state.
SCLK (output)
BUSY (bit)
CNT Cycles (6 shown)
SDATA (output)
Write -- No HiZ
D2
D3
D4
D5
D6
D7
EECTRL Byte Written
INT5
SDATA output Z
(LoZ)
Figure 9: 3-Wire Interface. Write Command, HiZ=0.
相关PDF资料
PDF描述
71M6521DE-IGT/F SPECIALTY ANALOG CIRCUIT, QFP64
71M6521FE-IGTR/F SPECIALTY ANALOG CIRCUIT, QFP64
71M6521DE-IMR/F SPECIALTY ANALOG CIRCUIT, QCC68
71M6521FE-IM/F SPECIALTY ANALOG CIRCUIT, QCC68
71M6521FE-IGT/F SPECIALTY ANALOG CIRCUIT, QFP64
相关代理商/技术参数
参数描述
71M6521-TGP1-68M 制造商:Maxim Integrated Products 功能描述:Programmer Accessories Gang Programmer Base w/6521 Socket Brd
71M6523-DB 功能描述:开发板和工具包 - 8051 71M6521D Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压:
71M6523-IM 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6523-IM/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6523-IMR 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel