- 您现在的位置：买卖IC网 > PDF目录20605 > 71M6533-IGTR/F (Maxim Integrated)IC ENERY METER 3PH 128K 100-LQFP PDF资料下载
参数资料
| 型号： | 71M6533-IGTR/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 39/132页 |
| 文件大小： | 0K |
| 描述： | IC ENERY METER 3PH 128K 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 系列： | Single Converter Technology® |
| 输入阻抗： | 40 千欧 ~ 90 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 10mA |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 三相，中性相位 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | * |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页
FDS_6533_6534_004
71M6533/G/H and 71M6534/H Data Sheet
The second rate adjustment is a digital rate adjust using PREG[16:0] and QREG[1:0] , which can be used
to adjust the clock rate up to ± 988 ppm, with a resolution of 3.8 ppm. Updates must occur after a one
second interrupt, and must finish before the next one second boundary. The rate adjustment will be
implemented starting at the next one-second boundary. Since the LSB results in an adjustment every
four seconds, the frequency should be measured over an interval that is a multiple of four seconds.
To adjust the clock rate using the digital rate adjust, the appropriate values must be written to PREG[16:0]
and QREG[1:0] . The default frequency is 32,768 RTCLK cycles per second. To shift the clock frequency
by ? ppm, calculate PREG[16:0] and QREG[1:0] using the following equation:
4 ? PREG + QREG = floor ?
? 1 + ? ? 10
+ 0 . 5 ?
? 32768 ? 8
? 6
?
?
For example, for a shift of -988 ppm, 4 ? PREG + QREG = 262403 = 0x40103. PREG[16:0] = 0x10040, and
QREG[1:0] = 0x03. The default values of PREG[16:0] and QREG[1:0] , corresponding to zero adjustment,
are 0x10000 and 0x0, respectively.
The RTC timing may be observed on the TMUXOUT pin by setting TMUX[4:0] to 0x10 or 0x11.
Default values for RTCA_ADJ[6:0] , PREG[16:0] and QREG[1:0] should be nominal values, at the
center of the adjustment range. Uncalibrated extreme values (zero, for example) can cause incorrect
operation.
If the crystal temperature coefficient is known, the MPU can integrate temperature and correct the RTC
time as necessary.
Both RTCA_ADJ[6:0] and PREG[16:0] / QREG[1:0 ] are non-volatile registers, i.e. their values will be
preserved in BROWNOUT, SLEEP and LCD modes. However, the digital correction controlled by the
PREG [16:0] / QREG [1:0] registers is not operational in SLEEP mode.
The digital adjustment using PREG[16:0] and QREG[1:0] is preferred over the analog adjustment using
RTCA_ADJ: The digital adjustment is more repeatable and has a wider range.
The sub-second register of the RTC, SUBSEC , can be read by the MPU after the one-second interrupt and
before reaching the next one second boundary. SUBSEC contains the count remaining, in 1/256 second
nominal clock periods, until the next one-second boundary. When the RST_SUBSEC bit is written, the
SUBSEC counter is restarted. Reading and resetting the sub-second counter can be used as part of an
algorithm to accurately set the RTC.
When setting the RTC_SEC register, it is important to take into account that the associated write operation
will be performed only in the next second boundary.
1.5.4
Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap
reference. If automatic temperature measurement is not performed by selecting CHOP_E[1:0] = 00, the
MPU may request an alternate multiplexer frame containing the temperature sensor output by asserting
MUX_ALT . The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system (see Section 3.5 Temperature Compensation ).
1.5.5
Physical Memory
Flash Memory
The device includes 128 KB (71M6533/H, 71M6534) or 256 KB (71M6533G, 71M6534H) of on-chip flash
memory. The flash memory primarily contains MPU and CE program code. It also contains images of
the CE and MPU data in RAM as well as of I/O RAM. On power-up, before enabling the CE, the MPU
copies these images to their respective locations.
Rev 2
39
相关PDF资料 |
PDF描述 |
|---|---|
| R1S-1215/HP | CONV DC/DC 1W 12VIN 15VOUT |
| SS10P4C-M3/86A | DIODE SCHOTTKY 10A 40V SMPC |
| ISL6534CRZ-T | IC REG TRPL BCK/LINEAR 32-QFN |
| R1S-1212/HP | CONV DC/DC 1W 12VIN 12VOUT |
| ABC43DRYS | CONN EDGECARD 86POS .100 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6534 | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC |
| 71M6534H | 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Energy Meter IC |
| 71M6534H-DB | 功能描述:开发板和工具包 - 8051 71M6534H Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 71M6534H-IGT/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6534H-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。