参数资料
| 型号： | 73610 |
| 厂商： | Desco |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | COAT LAB W/CUFFS BLUE XSMALL |
| 标准包装： | 1 |
| 系列： | Statshield® |
| 服装类型： | 实验室罩衣，带腕带 |
| 尺寸： | XSmall |
| 材质： | 聚酯 |
| 颜色： | 蓝 |
| 特点： | 胯部带 4mm 卡钉，袖口带导电织物 |
Installation
Follow the directions below for proper installation and
grounding of the Statshield smock.
1. Put on the smock and fasten all of the snaps on the front
of the smock, making sure that clothing is not exposed
outside of the smock.
2. Throughout use, it is essential that conductive cuff (or the
wristband) be in contact with operator’s skin; the
conductive cuff (or the wristband) should never be
allowed to be pulled up and over shirt sleeve.
3. Install a coil cord to the snap stud located above the left
hand hip pocket. Connect the other end of the coil cord
to a verified ground point or continuous monitor.
Grounding Integrity Testing
For daily testing or continuous monitoring of the grounding
integrity of Statshield smocks and ground cords, we
recommend testing the smock while worn and the use of
a standard wrist strap testers or single-wire workstation
continuous monitors. Panel-to-panel conductivity is essential
so as not to leave portions of the smock as isolated charged
conductors. Panel-to-panel conductivity is easy to test using
our Surface Resistance Meter Kit Item #
19787. Place the
two five-pound electrodes on different panels to test. Unless
properly grounded, the smocks can hold a charge and
become a possible source for discharge to ESD sensitive
items. For additional information, refer to ANSI/ESD S20.20,
ESD TR20.20, ESD TR53 and the Garment Standard,
ANSI/ESD STM2.1. Desco has several testers available
for this purpose. For more information ask for specification
drawings or operating instruction manuals by item number.
TB-2055 Page 3 of 4
2013 DESCO INDUSTRIES INC.
Employee Owned
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
Figure 5. Testing and monitoring of smock and ground
cord assembly
YES!
NO!
Figure 3. Proper installation of smock wearer’s body
Figure 4. Grounding the smock
Figure 6. Testers
NOTE: ANSI/ESD S20.20 RECOMMENDS THAT THE
GROUND COIL CORD SELECTED FOR GROUNDING OF
PERSONNEL CONTAIN A BUILT-IN CURRENT LIMITING
1 MEGOHM RESISTOR.
Heat Sealed Patches
It is possible to heat seal patches to our smocks. The patch
should be small and the smock should be tested before and
after application.
相关PDF资料 |
PDF描述 |
|---|---|
| 73607 | COAT LAB W/SNAPS BLUE 4XLARGE |
| 73606 | COAT LAB W/SNAPS BLUE 3XLARGE |
| 73600 | COAT LAB W/SNAPS BLUE XSMALL |
| 73646 | COAT LAB W/SNAPS TEAL 3XLARGE |
| 768163272GP | RES ARRAY 2.7K OHM 8 RES 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73-610-116 | 制造商:Emerson Network Power - Embedded Power 功能描述:- Bulk |
| 73-610-121 | 制造商:Emerson Network Power - Embedded Power 功能描述:- Bulk |
| 736-102 | 制造商:WAGO Innovative Connections 功能描述:TERMINAL BLOCK, PCB, 2POS, 28-12AWG; Connector Type:PCB Terminal Block; Series:736; Connector Mounting:PCB; Pitch Spacing:5mm; Approvals / Standards:(Not Available); No. of Contacts:2; Wire Size AWG Min:28AWG; Wire Size AWG Max:12AWG;RoHS Compliant: Yes |
| 736-103 | 制造商:WAGO Innovative Connections 功能描述:736 Series 3 Position Double Deck PCB Terminal Strip |
| 736-104 | 制造商:WAGO Innovative Connections 功能描述:TERMINAL BLOCK, PCB, 4POS, 28-12AWG; Connector Type:PCB Terminal Block; Series:736; Connector Mounting:PCB; Pitch Spacing:5mm; No. of Contacts:4; Wire Size AWG Min:28AWG; Wire Size AWG Max:12AWG; Contact Plating:Zinc; Color:Gray ;RoHS Compliant: Yes 制造商:WAGO Innovative Connections 功能描述:TERMINAL BLOCK, PCB, 4POS, 28-12AWG; Connector Type:PCB Terminal Block; Series:736; Connector Mounting:PCB; Pitch Spacing:5mm; Approvals / Standards:(Not Available); No. of Contacts:4; Wire Size AWG Min:28AWG; Wire Size AWG Max:12AWG;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。