参数资料
| 型号： | 73618 |
| 厂商： | Desco |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | COAT LAB W/CUFFS BLUE 5XLARGE |
| 标准包装： | 1 |
| 系列： | Statshield® |
| 服装类型： | 实验室罩衣，带腕带 |
| 尺寸： | 5XLarge |
| 材质： | 聚酯 |
| 颜色： | 蓝 |
| 特点： | 胯部带 4mm 卡钉，袖口带导电织物 |
Installation
Follow the directions below for proper installation and
grounding of the Statshield smock.
1. Put on the smock and fasten all of the snaps on the front
of the smock, making sure that clothing is not exposed
outside of the smock.
2. Throughout use, it is essential that conductive cuff (or the
wristband) be in contact with operator’s skin; the
conductive cuff (or the wristband) should never be
allowed to be pulled up and over shirt sleeve.
3. Install a coil cord to the snap stud located above the left
hand hip pocket. Connect the other end of the coil cord
to a verified ground point or continuous monitor.
Grounding Integrity Testing
For daily testing or continuous monitoring of the grounding
integrity of Statshield smocks and ground cords, we
recommend testing the smock while worn and the use of
a standard wrist strap testers or single-wire workstation
continuous monitors. Panel-to-panel conductivity is essential
so as not to leave portions of the smock as isolated charged
conductors. Panel-to-panel conductivity is easy to test using
our Surface Resistance Meter Kit Item #
19787. Place the
two five-pound electrodes on different panels to test. Unless
properly grounded, the smocks can hold a charge and
become a possible source for discharge to ESD sensitive
items. For additional information, refer to ANSI/ESD S20.20,
ESD TR20.20, ESD TR53 and the Garment Standard,
ANSI/ESD STM2.1. Desco has several testers available
for this purpose. For more information ask for specification
drawings or operating instruction manuals by item number.
TB-2055 Page 3 of 4
2013 DESCO INDUSTRIES INC.
Employee Owned
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
Figure 5. Testing and monitoring of smock and ground
cord assembly
YES!
NO!
Figure 3. Proper installation of smock wearer’s body
Figure 4. Grounding the smock
Figure 6. Testers
NOTE: ANSI/ESD S20.20 RECOMMENDS THAT THE
GROUND COIL CORD SELECTED FOR GROUNDING OF
PERSONNEL CONTAIN A BUILT-IN CURRENT LIMITING
1 MEGOHM RESISTOR.
Heat Sealed Patches
It is possible to heat seal patches to our smocks. The patch
should be small and the smock should be tested before and
after application.
相关PDF资料 |
PDF描述 |
|---|---|
| 73617 | COAT LAB W/CUFFS BLUE 4XLARGE |
| 73610 | COAT LAB W/CUFFS BLUE XSMALL |
| 73607 | COAT LAB W/SNAPS BLUE 4XLARGE |
| 73606 | COAT LAB W/SNAPS BLUE 3XLARGE |
| 73600 | COAT LAB W/SNAPS BLUE XSMALL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 7361866-KIT-ND | 制造商:DIGI-KEY KIT 功能描述:Customer Kit - Single |
| 73619 | 功能描述:COAT LAB W/CUFFS BLUE 6XLARGE RoHS:否 类别:静电控制，ESD，无尘室产品 >> 衣物 系列:Statshield® 标准包装:1 系列:Statshield® 服装类型:外套，带袖套 尺寸:6XLarge 材质:聚酯 颜色:青色 特点:胯部带 4mm 卡钉，袖口带导电织物 |
| 7361BA | 功能描述:散热片 1100-H14 AL. .8 in. X .71 in. RoHS:否 制造商:Ampro By ADLINK 产品:Heat Sink Accessories 安装风格:Through Hole 散热片材料: 散热片样式: 热阻: 长度: 宽度: 高度: 设计目的:Express-HRR |
| 7-361-BA | 功能描述:HEATSINK VERT HORZ TO-220 RoHS:是 类别:风扇，热管理 >> 热敏 - 散热器 系列:7 产品目录绘图:BDN12-3CB^A01 标准包装:300 系列:BDN 类型:顶部安装 冷却式包装:分类（BGA，LGA，CPU，ASIC……） 固定方法:散热带，粘合剂（含） 形状:方形，鳍片 长度:1.21"（30.73mm） 宽:1.210"（30.73mm） 直径:- 机座外的高度（散热片高度）:0.355"（9.02mm） 温升时的功耗:- 在强制气流下的热敏电阻:在 400 LFM 时为6.8°C/W 自然环境下的热电阻:19.6°C/W 材质:铝 材料表面处理:黑色阳极化处理 产品目录页面:2681 (CN2011-ZH PDF) 其它名称:294-1099 |
| 7-361-BAP | 制造商:CTS Corporation 功能描述:Heat Sink Passive Aluminum Black Anodized |
发布紧急采购，3分钟左右您将得到回复。