- 您现在的位置：买卖IC网 > PDF目录68812 > 73M1903-IVT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO20 PDF资料下载
参数资料
| 型号： | 73M1903-IVT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封装： | ROHS COMPLIANT, MO-153AC, TSSOP-20 |
| 文件页数： | 2/47页 |
| 文件大小： | 541K |
| 代理商： | 73M1903-IVT/F |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页
73M1903 Data Sheet
DS_1903_032
10
Rev. 2.1
2.1
GPIO
The 73M1903 modem AFE device provides 8 user defined I/O pins. Each pin is programmed separately
as either an input or an output by a bit in a direction register. If the bit in the direction register is set high,
the corresponding pin is an input whose value is read from the GPIO data register. If it is low, the pin will
be treated as an output whose value is set by the GPIO data register.
To avoid unwanted current contention and consumption in the system from the GPIO port before the
GPIO is configured after a reset, the GPIO port I/Os are initialized to a high impedance state. The input
structures are protected from floating inputs, and no output levels are driven by any of the GPIO pins.
The GPIO pins are configured as inputs or outputs when the host controller (or DSP) writes to the GPIO
direction register. The GPIO direction and data registers are initialized to all ones (FFh) upon reset.
2.1.1
GPIO Data (GPIO): Address 02h
Reset State FFh
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
GPIO7
GPIO6
GPIO5
GPIO4
GPIO3
GPIO2
GPIO1
GPIO0
Bits in this register will be asserted on the GPIO(7:0) pins if the corresponding direction register bit is a 0.
Reading this address will return data reflecting the values of pins GPIO(7:0).
2.1.2
GPIO Direction (DIR): Address 03h
Reset State FFh
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
DIR7
DIR6
DIR5
DIR4
DIR3
DIR2
DIR1
DIR0
This register is used to designate the GPIO pins as either inputs or outputs. If the register bit is low, the
corresponding GPIO pin is programmed as an output. If the register bit is a 1, the corresponding pin will
be treated as an input.
2.2
Analog I/O
Figure 4 shows the block diagram of the analog front end. The analog interface circuit uses differential
transmit and receive signals to and from the external circuitry.
The hybrid driver in the 73M1903 IC is capable of connecting directly, but not limited to, a transformer-
based Direct Access Arrangement (DAA). The hybrid driver is capable of driving the DAA’s line coupling
transformer, which carries an impedance on the primary side that is typically rated at 600
Ω, depending
on the transformer and matching network. The hybrid drivers can also drive high impedance loads
without modification. The class AB behavior of the amplifiers provides load dependent power
consumption.
An on-chip band gap voltage is used to provide an internal voltage reference and bias currents for the
analog receive and transmit channels. The reference derived from the bandgap, nominally 1.25 Volts, is
multiplied to 1.36 Volts and output at the VREF pin. Several voltage references, nominally 1.25 Volts, are
used in the analog circuits. The band gap and reference circuits are disabled after a chip reset since the
ENFE bit is reset to a default state of zero. When ENFE=0, the band gap voltage and the analog bias
currents are disabled. In
this case all of the analog circuits are powered down and draw less than 5 μA of
current.
A clock generator (CKGN) is used to create all of the non-overlapping phase clocks needed for the time
sampled switched-capacitor circuits, ASDM, DAC1, and TLPF. The CKGN input is two times the
analog/digital interface sample rate or 3.072 MHz clock for Fs=8 kHz.
相关PDF资料 |
PDF描述 |
|---|---|
| 73M1903-IVTR/F | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 73M1903C-IM/F | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 73M1903C-IMR/F | SPECIALTY CONSUMER CIRCUIT, PQCC32 |
| 73M1903C-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 73M1903C-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73M1903-IVTR/F | 功能描述:IC MODEM AFE V.22BIS 20-TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模拟前端 (AFE) 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 位数:- 通道数:2 功率（瓦特）:- 电压 - 电源，模拟:3 V ~ 3.6 V 电压 - 电源，数字:3 V ~ 3.6 V 封装/外壳:32-VFQFN 裸露焊盘 供应商设备封装:32-QFN（5x5） 包装:带卷 (TR) |
| 73M1906B-IM/F | 功能描述:电信线路管理 IC DAA-FXO VOLP System Host Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1906B-IM/F1 | 功能描述:电信线路管理 IC RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1906B-IMR/F | 功能描述:电信线路管理 IC DAA-FXO VOLP System Host Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| 73M1906B-IMR/F1 | 功能描述:电信线路管理 IC RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。