参数资料
型号: 73M1916-IVT/F
厂商: Maxim Integrated Products
文件页数: 68/88页
文件大小: 0K
描述: MICRODAA SET FXO OF VOIP 20TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 74
系列: MicroDAA™
功能: 数据存取装置(DAA)
接口: PCM,SPI
电路数: 1
电源电压: 3 V ~ 3.6 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 20-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 20-TSSOP
包装: 散装
包括: *
73M1866B/73M1966B Data Sheet
DS_1x66B_001
70
Rev. 1.6
Function
Mnemonic
Register
Location
Type
Description
ENLVD
0x12[3]
WO
LeV Detection (OVDET, UVDET, OIDET monitors)
0 = Enable LeV detection. (Default)
1 = Disable LeV detection (used in line-powered mode to save power).
This bit will be 0 when Line Powered Mode is detected (ENLPW is set
in Register 0x02[2]) and set to 1 when an interrupt occurs within the
73M1916. This bit must be reset prior to switching back to Barrier
Powered Mode.
ENNOM
0x12[0]
WO
Enable Nominal Operation
0 = Speeds up the on and off hook transitions time by increasing the
DC loop bandwidth of the DC transconductance circuit in the
73M1x66B. This should be used for pulse dialing, going on and off
hook, etc. In addition, ENNOM=0 prevents the reset of all bits in
Register 0x12. (Default)
1 = Enter Nominal Operation. Reduces the loop bandwidth of the DC
transconductance circuit. Allows reset of Register 0x12 caused by bits
UVDET, OVDET or OIDET.
ENSHL
0x12[4]
WO
Enable Shunt Loading
0 = Disable shunt loading. (Default)
1 = Enable shunt loading of the line. Not used for most applications.
IDISPD
0x13[1]
WO
Discharge and Pulse Dialing
Controls the DC discharge current and how fast the loop turns off.
Affects pulse dialing waveform. Controls the amount of discharge
current during hook switch transitions.
0 = Minimum current. (Default)
1 = Maximum current.
It is recommended to set IDISPD to 1 prior to hook switching
operations.
ILM
0x13[5]
WO
Current Limit Enable
This control enables or disables loop current limit.
0 = No current limit. (Default)
1 = 42 mA current limit enabled.
ILMON
0x1E[7]
R
Current Limit Mode On
This status bit is effective only when the ILM bit is set to 1.
0 = Loop current is lower than 42 mA.
1 = Loop current is higher than 42 mA and the current limiting mode is
active.
OFH
0x12[7]
WO
Off-Hook Enable
This bit controls the state of the Hook signal.
0 = On-Hook. (Default)
1 = Off-Hook.
PLDM
0x13[3]
WO
Pulse Dialing Mode Enable
Alleviates the strict timing requirements for the Host having to control
ENDC and OFH during pulse dialing. With PLDM = 1, the Host only
has to toggle OFH to perform pulse dialing.
0 = Pulse Dialing Mode is disabled. (Default)
1 = Pulse Dialing Mode is enabled.
RLPNEN
0x16[5]
W
Receive Low Pass Notch Enable
0 = Billing Tone Receive Low Pass Notch (RLPN) filter bypassed.
(Default)
1 = RLPN Filter Enabled. See RLPNH for notch frequency selection.
相关PDF资料
PDF描述
73M1916-IVTR/F MICRODAA SET FXO OF VOIP 20TSSOP
MC908QY4CDWER IC MCU 8BIT 4K FLASH 16-SOIC
MC908QY4ACDWER IC MCU 8BIT 4K FLASH 16-SOIC
S9S08SL8F1CTJ IC MCU 8BIT 8KB FLASH 20TSSOP
VI-22T-IX-S CONVERTER MOD DC/DC 6.5V 75W
相关代理商/技术参数
参数描述
73M1916-IVTR/F 功能描述:电信线路管理 IC DAA-FXO VOLP System Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray
73M1922-DB 功能描述:网络开发工具 73M1922 Demo Brd RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
73M1966B-DB 功能描述:网络开发工具 73M1966B Demo Brd RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
73M1966B-DB-C 功能描述:网络开发工具 73M1966B Demo Brd w/GUI Cable RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V
73M1966B-EVM 功能描述:网络开发工具 73M1966 Demo Brd & MotherBrd RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V