- 您现在的位置：买卖IC网 > PDF目录1888 > 73S8010C-ILR/F (Maxim Integrated Products)IC SMART CARD INTERFACE 28-SOIC PDF资料下载
参数资料
| 型号： | 73S8010C-ILR/F |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 26/27页 |
| 文件大小： | 0K |
| 描述： | IC SMART CARD INTERFACE 28-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,500 |
| 控制器类型： | 智能卡接口 |
| 接口： | I²C |
| 电源电压： | 2.7 V ~ 3.6 V |
| 电流 - 电源： | 4.9mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页
73S8010C Data Sheet
DS_8010C_024
8
Rev. 1.5
ACK bit is sent to the master by the device. The master should send the STOP condition after receiving
the ACK bit.
Figure 2: I
2C Bus Write Protocol
2.2
Host Interface Status
Table 3 describes the Host Interface Status Register bits (power-on Reset = 0x04).
Table 3: Host Status Register
Name
Bit
Description
PRES
0
Set when the card is present; reset when the card is not present.
PRESL
1
Set when the PRES pin changes state (rising/falling edge); reset when the status
register is read. Generates an interrupt when set
I/O
2
Set when I/O is high; reset when I/O is low.
SUPL
3
Set when a voltage fault is detected; reset when the status register is read.
Generates an interrupt when set.
PROT
4
Set when an over-current or over-heating fault has occurred during a card session;
reset when the status register is read. Generates an interrupt when set.
MUTE
5
Set during ATR when the card has not answered during the ISO 7816-3 time
window (40000 card clock cycles); reset when the next session begins or this
register is read.
EARLY
6
Set during ATR when the card has answered before 400 card clock cycles; reset
when the next session begins or this register is read.
ACTIVE
7
Set when the card is active (VCC is on); reset when the card is inactive.
I
2C-bus Read from the Status Register:
The I
2C-bus Read Command from the Status Register follows the format shown in Figure 3.
After the START condition, the master sends a slave address. This address is seven bits long followed
by an eighth bit, which is the opcode bit (R/
W). A ‘one’ indicates the master will read data from the status
register. After the R/
W bit, the ’zero’ ACK bit is sent to the master by the device. The device now starts
sending the 8-bit status register data to the control register during the DATA bits time. After the DATA
bits, the ‘one’ ACK bit is sent to the device by the master. The master should send the STOP condition
after receiving the ACK bit.
相关PDF资料 |
PDF描述 |
|---|---|
| 73S8010R-ILR/F | IC SMART CARD INTERFACE 28-SOIC |
| 73S8014R-IL/F | IC SMART CARD 7816 EMV 20-SOIC |
| 73S8014RN-ILR/F | IC SMART CARD 7816 EMV 20-SOIC |
| 73S8023C-IMR/F | IC SMART CARD INTERFACE 32-QFN |
| 73S8024C-ILR/F | IC SMART CARD INTERFACE 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 73S8010C-IM/F | 功能描述:I2C 接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010C-IM/F2 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010C-IMR/F | 功能描述:I2C 接口集成电路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010C-IMR/F1 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
| 73S8010C-IMR/F2 | 功能描述:I2C 接口集成电路 RoHS:否 制造商:NXP Semiconductors 电源电压-最大:5.5 V 电源电压-最小:2.3 V 最大工作频率:400 KHz 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-16 |
发布紧急采购，3分钟左右您将得到回复。