参数资料
| 型号： | 748636-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/4页 |
| 文件大小： | 0K |
| 描述： | CONN KIT HD D-SUB RECEPT 44PO |
| 标准包装： | 100 |
| 系列： | AMPLIMITE HDP-22 |
| 连接器类型： | 母触点插座 |
| 位置数： | 44 |
| 连接器类型： | D-Sub，高密度 |
| 触点类型：： | 信号 |
| 行数： | 3 |
| 外壳尺寸，连接器布局： | 3（DB，B）高密度 |
| 法兰特点： | 空心，无螺纹 |
| 安装类型： | 自由悬挂 |
| 外壳材料，表面处理： | 钢，镀锡 |
| 特点： | 组件套件，屏蔽 |
| 请注意： | 不提供触点 |
| 包装： | 散装 |
| 电介质材料： | 热塑塑胶 |
| 颜色： | 黑 |
408- 9010
5. For HDE--20 connectors, obtain 3M V Scotch
Tape 44 (or equivalent), 9.53 mm [.375 in.] wide.
Wrap the tape around the terminated contacts two
complete times. See Figure 4.
HDE-- 20
9.53 mm
Connector (Ref)
[.375 in.]
HDE-- 20
Connector
HDP-- 20, HDP-- 22
Connector
Terminated
Strip Length
Wrapped
Tape
Tape (Two Wraps)
Wire
Bundle
Braid
Ferrule
!
CONNECTOR
CONTACT
TYPE
POSITION
Figure 4
4. SHIELD ASSEMBLY PROCEDURE
1. Measure the terminated length of the assembly
as shown in Figure 5.
CAUTION The length must be as indicated in Figure 5 and
must conform to the configuration as shown in
the illustration; otherwise, wires may be pinched
between the shields when they are closed. The
proper length and configuration may be achieved
by twisting (and thereby shortening) the wire
bundle after termination; however, make certain
that no undue stress is placed on the terminated
contacts during the procedure. The MAXIMUM
amount that the bundle may be twisted to
achieve the desired length is 90 _ .
2. Insert the hinge tabs of the inner shield into the
corresponding slots of the connector and rotate the
shield 90 _ toward the cable. See Figure 6.
3. Insert the hinge tabs of the outer shield into the
corresponding slots of the connector. See Figure 6.
4. Make sure that the inner shield is in its final
position and close the outer shield until it latches
onto the inner shield with the two latching tabs fully
engaged. See Figure 7.
V Trademark of Minnesota Mining & Manufacturing Co.
Rev C
Cable
Jacket
TERMINATED
STRIP LENGTH
+1.27 [+.050] (mm [in.])
9, 15, 25 33.02 [1.300]
HDE--20
37 38.10 [1.500]
9, 15, 25 33.02 [1.300]
HDP--20 37 40.64 [1.600]
50 38.10 [1.500]
15, 26, 44 33.02 [1.300]
HDP--22 62 40.64 [1.600]
78 38.10 [1.500]
Figure 5
CAUTION Take care not to pinch any individual wires
between the shields.
!
5. Slide the braid over the braid crimp area of the
mated shields. See Figure 7.
6. Slide ferrule forward until it is over the braid and
butted against the shield assembly.
3 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 748826-2 | CONN D-SUB PLUG R/A 25POS T/H |
| 748865-3 | CONN D-SUB PLUG R/A 25POS |
| 748904-1 | CONN D-SUB PLUG R/A 15POS |
| 748948-1 | CONN D-SUB RECEPT R/A 15POS |
| 748979-1 | CONN D-SUB RECPT R/A 9POS PCB AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 748637-1 | 功能描述:D-Sub标准连接器 62P RECEPTACLE RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤: |
| 748639-1 | 功能描述:D-Sub标准连接器 RECEPTACLE KIT 15P RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤: |
| 748640-1 | 功能描述:D-Sub标准连接器 26P RECPT ENCL KIT RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤: |
| 748640-1-KIT | 制造商:TE CONNECTIVITY 功能描述:26 RECPT SHIELD ENCL KIT |
| 748641-1 | 制造商:TE Connectivity 功能描述:44 HDP SHLD ENCLSR RCPT, BULK - Bulk 制造商:TE Connectivity 功能描述:Conn Housing RCP 44 POS Crimp ST Bulk |
发布紧急采购，3分钟左右您将得到回复。