- 您现在的位置：买卖IC网 > PDF目录15263 > LTC3834IFE#PBF (Linear Technology)IC REG CTRLR BUCK PWM CM 20TSSOP PDF资料下载
参数资料
| 型号： | LTC3834IFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 20TSSOP |
| 标准包装： | 74 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 580kHz |
| 占空比： | 99.4% |
| 电源电压： | 4 V ~ 36 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽）裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC3834
OPERATION (Refer to Functional Diagram)
When the RUN pin is pulled low to disable the LTC3834, or
when V IN drops below its undervoltage lockout threshold
of 3.7V, the TRACK/SS pin is pulled low by an internal
MOSFET. When in undervoltage lockout, the controller is
disabled and the external MOSFETs are held off.
Light Load Current Operation (Burst Mode Operation,
Pulse-Skipping or Continuous Conduction)
(PLLIN/MODE Pin)
The LTC3834 can be enabled to enter high ef?ciency
Burst Mode operation, constant-frequency pulse-skipping
mode, or forced continuous conduction mode at low load
currents. To select Burst Mode operation, tie the PLLIN/
MODE pin to a DC voltage below 0.8V (e.g., SGND). To
select forced continuous operation, tie the PLLIN/MODE
pin to INTV CC . To select pulse skipping mode, tie the
PLLIN/MODE pin to a DC voltage greater than 0.8V and
less than INTV CC – 0.5V.
When the LTC3834 is enabled for Burst Mode operation,
the peak current in the inductor is set to approximately
one-tenth of the maximum sense voltage even though the
voltage on the I TH pin indicates a lower value. If the aver-
age inductor current is lower than the load current, the
error ampli?er EA will decrease the voltage on the I TH pin.
When the I TH voltage drops below 0.4V, the internal sleep
signal goes high (enabling “sleep” mode) and both external
MOSFETs are turned off. The I TH pin is then disconnected
from the output of the EA and “parked” at 0.425V.
In sleep mode, much of the internal circuitry is turned off,
reducing the quiescent current that the LTC3834 draws to
only 30μA. In sleep mode, the load current is supplied by
the output capacitor. As the output voltage decreases, the
EA’s output begins to rise. When the output voltage drops
enough, the I TH pin is reconnected to the output of the
normal operation by turning on the top external MOSFET
on the next cycle of the internal oscillator.
When the LTC3834 is enabled for Burst Mode operation,
the inductor current is not allowed to reverse. The reverse
current comparator (RI CMP ) turns off the bottom external
MOSFET just before the inductor current reaches zero,
preventing it from reversing and going negative, thus
operating in discontinuous operation.
In forced continuous operation, the inductor current is
allowed to reverse at light loads or under large transient
conditions. The peak inductor current is determined by the
voltage on the I TH pin, just as in normal operation. In this
mode, the ef?ciency at light loads is lower than in Burst
Mode operation. However, continuous operation has the
advantages of lower output ripple and less interference
to audio circuitry. In forced continuous mode, the output
ripple is independent of load current.
When the PLLIN/MODE pin is connected for pulse skip-
ping mode or clocked by an external clock source to
use the phase-locked loop (see Frequency Selection and
Phase-Locked Loop section), the LTC3834 operates in
PWM pulse skipping mode at light loads. In this mode,
constant-frequency operation is maintained down to ap-
proximately 1% of designed maximum output current.
At very light loads, the current comparator ICMP may
remain tripped for several cycles and force the external top
MOSFET to stay off for the same number of cycles (i.e.,
skipping pulses). The inductor current is not allowed to
reverse (discontinuous operation). This mode, like forced
continuous operation, exhibits low output ripple as well as
low audio noise and reduced RF interference as compared
to Burst Mode operation. It provides higher low current
ef?ciency than forced continuous mode, but not nearly as
high as Burst Mode operation.
EA, the sleep signal goes low, and the controller resumes
3834fb
11
相关PDF资料 |
PDF描述 |
|---|---|
| SRP1235-4R7M | INDUCTOR 4.7UH 10A SMD |
| LTC1735CGN | IC REG CTRLR BUCK PWM CM 16-SSOP |
| SRP1235-6R8M | INDUCTOR 6.8UH 9A SMD |
| LTC3789EUFD#TRPBF | IC REG CTRLR BST PWM CM 28-QFN |
| SXR122M025ST | CAP ALUM 1200UF 25V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74AHC273BQ-G | 功能描述:触发器 OCTAL D FLIP-FLOP RoHS:否 制造商:Texas Instruments 电路数量:2 逻辑系列:SN74 逻辑类型:D-Type Flip-Flop 极性:Inverting, Non-Inverting 输入类型:CMOS 输出类型: 传播延迟时间:4.4 ns 高电平输出电流:- 16 mA 低电平输出电流:16 mA 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:X2SON-8 封装:Reel |
| 74AHC273BQ-Q100X | 制造商:NXP Semiconductors 功能描述:Flip Flop D-Type Bus Interface Pos-Edge 1-Element 20-Pin DHVQFN EP T/R 制造商:NXP Semiconductors 功能描述:74AHC273BQ-Q100/DHVQFN20/REEL7 - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC FLIP-FLOP OCTAL D 20DHVQFN |
| 74AHC273D | 功能描述:触发器 OCTAL D W/R POS EDGE RoHS:否 制造商:Texas Instruments 电路数量:2 逻辑系列:SN74 逻辑类型:D-Type Flip-Flop 极性:Inverting, Non-Inverting 输入类型:CMOS 输出类型: 传播延迟时间:4.4 ns 高电平输出电流:- 16 mA 低电平输出电流:16 mA 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:X2SON-8 封装:Reel |
| 74AHC273D,112 | 功能描述:触发器 OCTAL D W/R POS EDGE RoHS:否 制造商:Texas Instruments 电路数量:2 逻辑系列:SN74 逻辑类型:D-Type Flip-Flop 极性:Inverting, Non-Inverting 输入类型:CMOS 输出类型: 传播延迟时间:4.4 ns 高电平输出电流:- 16 mA 低电平输出电流:16 mA 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:X2SON-8 封装:Reel |
| 74AHC273D,118 | 功能描述:触发器 OCTAL D W/R POS EDGE RoHS:否 制造商:Texas Instruments 电路数量:2 逻辑系列:SN74 逻辑类型:D-Type Flip-Flop 极性:Inverting, Non-Inverting 输入类型:CMOS 输出类型: 传播延迟时间:4.4 ns 高电平输出电流:- 16 mA 低电平输出电流:16 mA 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:X2SON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。