参数资料
型号: 74AHC595
厂商: NXP Semiconductors N.V.
英文描述: 8-bit serial-in/serial or parallel-out shift register with output latches;3-state(带输出锁存的8位串行输入/串行或并行输出移位寄存器;三态)
中文描述: 8位serial-in/serial或并行输出的移位寄存器输出锁存器,3态(带输出锁存的8位串行输入/串行或并行输出移位寄存器,三态)
文件页数: 18/20页
文件大小: 103K
代理商: 74AHC595
2000 Mar 15
18
Philips Semiconductors
Product specification
8-bit serial-in/serial or parallel-out shift
register with output latches; 3-state
74AHC595; 74AHCT595
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相关PDF资料
PDF描述
74AHCT595 8-bit serial-in/serial or parallel-out shift register with output latches;3-state(带输出锁存的8位串行输入/串行或并行输出移位寄存器;三态)
74AHC74 Dual D-type flip-flop with set and reset; positive-edge trigger(带置位和复位的双D触发器;上升沿触发;)
74AHC74PWDH Dual D-type flip-flop with set and reset; positive-edge trigger
74AHCT74PWDH Dual D-type flip-flop with set and reset; positive-edge trigger
74AHCT74 Dual D-type flip-flop with set and reset; positive-edge trigger(带置位和复位的双D触发器;上升沿触发;)
相关代理商/技术参数
参数描述
74AHC595_09 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:NPN general-purpose double transistors output latches; 3-state
74AHC595BQ 制造商:NXP Semiconductors 功能描述:IC 8BIT SHFT REG TRI-ST DHVQFN16 制造商:NXP Semiconductors 功能描述:IC, 8BIT, SHFT REG, TRI-ST, DHVQFN16 制造商:NXP Semiconductors 功能描述:IC, 8BIT, SHFT REG, TRI-ST, DHVQFN16, Shift Register Function:Serial to Parallel
74AHC595BQ,115 功能描述:计数器移位寄存器 5V 8 SHIFT REG OTPT RoHS:否 制造商:Texas Instruments 计数器类型: 计数顺序:Serial to Serial/Parallel 电路数量:1 封装 / 箱体:SOIC-20 Wide 逻辑系列: 逻辑类型: 输入线路数量:1 输出类型:Open Drain 传播延迟时间:650 ns 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装:Reel
74AHC595BQ-G 功能描述:计数器移位寄存器 5V 8 SHIFT REG OTPT LATCH 3S RoHS:否 制造商:Texas Instruments 计数器类型: 计数顺序:Serial to Serial/Parallel 电路数量:1 封装 / 箱体:SOIC-20 Wide 逻辑系列: 逻辑类型: 输入线路数量:1 输出类型:Open Drain 传播延迟时间:650 ns 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装:Reel
74AHC595BQ-Q100,11 制造商:NXP Semiconductors 功能描述:74AHC595BQ-Q100/DHVQFN16/REEL7 - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC SHIFT REGISTER 8BIT 16DHVQFN