- 您现在的位置：买卖IC网 > PDF目录360408 > 74AHCT04PWDH (NXP SEMICONDUCTORS) CERAMIC CHIP/MIL-PRF-55681 PDF资料下载
参数资料
| 型号： | 74AHCT04PWDH |
| 厂商： | NXP SEMICONDUCTORS |
| 元件分类： | 通用总线功能 |
| 英文描述： | CERAMIC CHIP/MIL-PRF-55681 |
| 中文描述： | AHCT/VHCT SERIES, HEX 1-INPUT INVERT GATE, PDSO14 |
| 封装： | 4.40 MM, PLASTIC, SOT-402-1, TSSOP-14 |
| 文件页数： | 11/16页 |
| 文件大小： | 73K |
| 代理商： | 74AHCT04PWDH |
1999 Sep 27
11
Philips Semiconductors
Product specification
Hex inverter
74AHC04; 74AHCT04
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相关PDF资料 |
PDF描述 |
|---|---|
| 74AHCT08 | Quad 2-input AND gate(四2输入与门) |
| 74AHC08 | Quad 2-input AND gate |
| 74AHC08PWDH | Quad 2-input AND gate |
| 74AHCT08PWDH | Quad 2-input AND gate |
| 74AHCT123A | Dual retriggerable monostable multivibrator with reset(带复位的双路可再触发单稳态多谐振荡器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74AHCT04PW-Q100J | 制造商:NXP Semiconductors 功能描述:74AHCT04PW-Q100/TSSOP14/REEL13 - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC HEX INVERTER 14TSSOP |
| 74AHCT04PW-T | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Hex Inverter |
| 74AHCT04S14-13 | 制造商:Diodes Incorporated 功能描述:AHC TTL COMPATIBLE HIGH PIN COUNT SO-14 T&R 2.5K - Tape and Reel 制造商:Diodes Incorporated 功能描述:IC GATE 2.5K SO14 制造商:Diodes Incorporated 功能描述:74AHCT Series 5.5 V Surface Mount HEX Inverter - SOIC-14 |
| 74AHCT04T14-13 | 制造商:Diodes Incorporated 功能描述:IC GATE 2.5K TSSOP14 制造商:Diodes Incorporated 功能描述:74AHCT Series 5.5 V Surface Mount HEX Inverter - TSSOP-14 |
| 74AHCT07APWJ | 功能描述:74AHCT07APW/SOT402/TSSOP14 制造商:nexperia usa inc. 系列:74AHCT 零件状态:在售 逻辑类型:缓冲器，非反向 元件数:1 每元件位数:6 输入类型:- 输出类型:开路漏极 电流 - 输出高，低:-，8mA 电压 - 电源:4.5 V ~ 5.5 V 工作温度:-40°C ~ 125°C（TA） 安装类型:表面贴装 封装/外壳:14-TSSOP（0.173"，4.40mm 宽） 供应商器件封装:14-TSSOP 标准包装:2,500 |
发布紧急采购，3分钟左右您将得到回复。