- 您现在的位置：买卖IC网 > PDF目录2024 > 74ALVCH16543DGG:11 (NXP Semiconductors)IC TRANSCVR TRI-ST 16BIT 56SSOP PDF资料下载
参数资料
| 型号： | 74ALVCH16543DGG:11 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC TRANSCVR TRI-ST 16BIT 56SSOP |
| 产品培训模块： | Logic Packages |
| 标准包装： | 35 |
| 系列： | 74ALVCH |
| 逻辑类型： | 寄存收发器，非反相 |
| 元件数： | 2 |
| 每个元件的位元数： | 8 |
| 输出电流高，低： | 24mA，24mA |
| 电源电压： | 1.2 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-TFSOP（0.240"，6.10mm 宽） |
| 供应商设备封装： | 56-TSSOP |
| 包装： | 管件 |
| 其它名称： | 74ALVCH16543DG 74ALVCH16543DG-ND 935262544112 |
1999 Nov 23
15
Philips Semiconductors
Product specication
16-bit D-type registered transceiver; 3-state
74ALVCH16543
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°C. The top-surface temperature of the
packages should preferable be kept below 230
°C.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit boards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is preferred to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint must
be placed at a 45
° angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°C.
相关PDF资料 |
PDF描述 |
|---|---|
| 74ALVCH16646DGG,11 | IC TRANSCVR 16BIT N-INV 56TSSOP |
| 74ALVCH16652DGG:11 | IC 16BIT TXRX/REGISTER 56TSSOP |
| 74ALVCH16832DGG,11 | IC ADDRESS REGISTER DVR 64TSSOP |
| 74ALVCHS162830DGB: | IC ADDRESS DVR 18-36BIT 80TSSOP |
| 74ALVCHT16835DGV:1 | IC REGISTERED DVR 16BIT 56TVSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74ALVCH16543DGGRE4 | 功能描述:总线收发器 16B Reg Trnscvr RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
| 74ALVCH16543DGGRG4 | 功能描述:总线收发器 16B Reg Xceiver RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
| 74ALVCH16543DGGS | 功能描述:IC TXRX 16BIT TRI-ST 56TSSOP 制造商:nexperia usa inc. 系列:74ALVCH 包装:管件 零件状态:在售 逻辑类型:收发器，非反相 元件数:2 每元件位数:8 输入类型:- 输出类型:推挽式 电流 - 输出高，低:24mA，24mA 电压 - 电源:1.2 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:56-TFSOP（0.240"，6.10mm 宽） 供应商器件封装:56-TSSOP 标准包装:35 |
| 74ALVCH16543DGGY | 功能描述:Transceiver, Non-Inverting 2 Element 8 Bit per Element Push-Pull Output 56-TSSOP 制造商:nxp semiconductors 系列:74ALVCH 包装:带卷（TR） 零件状态:有效 逻辑类型:收发器，非反相 元件数:2 每元件位数:8 输入类型:- 输出类型:推挽式 电流 - 输出高，低:24mA，24mA 电压 - 电源:1.2 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:56-TFSOP（0.240"，6.10mm 宽） 供应商器件封装:56-TSSOP 标准包装:2,000 |
| 74ALVCH16543DG-T | 功能描述:总线收发器 16-BIT LATCH XCVR 3-S RoHS:否 制造商:Fairchild Semiconductor 逻辑类型:CMOS 逻辑系列:74VCX 每芯片的通道数量:16 输入电平:CMOS 输出电平:CMOS 输出类型:3-State 高电平输出电流:- 24 mA 低电平输出电流:24 mA 传播延迟时间:6.2 ns 电源电压-最大:2.7 V, 3.6 V 电源电压-最小:1.65 V, 2.3 V 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。