- 您现在的位置：买卖IC网 > PDF目录360418 > 74AUC1G08 (NXP Semiconductors N.V.) 16 AMP MINIATURE PC BOARD RELAY PDF资料下载
参数资料
| 型号： | 74AUC1G08 |
| 厂商： | NXP Semiconductors N.V. |
| 英文描述： | 16 AMP MINIATURE PC BOARD RELAY |
| 中文描述： | 单2输入与门 |
| 文件页数： | 10/12页 |
| 文件大小： | 50K |
| 代理商： | 74AUC1G08 |
2002 Nov 12
10
Philips Semiconductors
Preliminary specification
Single 2-input NAND gate
74AUC1G00
SOLDERING
Introduction to soldering surface mount packages
This text gives a very brief insight to a complex
technology. A more in-depth account of soldering ICs can
be found in our “Data Handbook IC26; Integrated Circuit
Packages”(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering can still be used for
certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is
recommended.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package
placement.
Several methods exist for reflowing; for example,
convection or convection/infrared heating in a conveyor
type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending
on heating method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 220
°
C for
thick/large packages, and below 235
°
C for small/thin
packages.
Wave soldering
Conventional single wave soldering is not recommended
for surface mount devices (SMDs) or printed-circuit
boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by
a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
For packages with leads on four sides, the footprint
must be placed at a 45
°
angle to the transport direction
of the printed-circuit board. The footprint must
incorporate solder thieves downstream and at the side
corners.
During placement and before soldering, the package
must be fixed with a droplet of adhesive. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相关PDF资料 |
PDF描述 |
|---|---|
| 74AUC1G08GV | Single 2-input AND gate |
| 74AUC1G08GW | Single 2-input AND gate |
| 74AUC1G02 | 74AUC1G02 Single 2-input NOR gate |
| 74AUC1G02GV | 74AUC1G02 Single 2-input NOR gate |
| 74AUC1G02GW | 74AUC1G02 Single 2-input NOR gate |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74AUC1G08GV | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single 2-input AND gate |
| 74AUC1G08GW | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Single 2-input AND gate |
| 74AUC1G125DBVRE4 | 功能描述:缓冲器和线路驱动器 Single Bus Buffer Gate RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| 74AUC1G125DBVRG4 | 功能描述:缓冲器和线路驱动器 Single Bus Buffer Gate RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
| 74AUC1G125DCKRE4 | 功能描述:缓冲器和线路驱动器 Single Bus Buffer Gate RoHS:否 制造商:Micrel 输入线路数量:1 输出线路数量:2 极性:Non-Inverting 电源电压-最大:+/- 5.5 V 电源电压-最小:+/- 2.37 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。