- 您现在的位置：买卖IC网 > PDF目录8060 > 74HC191DB,118 (NXP Semiconductors)IC 4BIT BINAR UP/DN COUNT 16SSOP PDF资料下载
参数资料
| 型号： | 74HC191DB,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | IC 4BIT BINAR UP/DN COUNT 16SSOP |
| 产品培训模块： | Logic Packages |
| 标准包装： | 2,000 |
| 系列： | 74HC |
| 逻辑类型： | 二进制计数器 |
| 方向： | 上，下 |
| 元件数： | 1 |
| 每个元件的位元数： | 4 |
| 计时： | 同步 |
| 计数速率： | 39MHz |
| 触发器类型： | 正边沿 |
| 电源电压： | 2 V ~ 6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | 74HC191DB-T 74HC191DB-T-ND 935188600118 |
December 1990
2
Philips Semiconductors
Product specication
Presettable synchronous 4-bit binary
up/down counter
74HC/HCT191
FEATURES
Synchronous reversible counting
Asynchronous parallel load
Count enable control for synchronous expansion
Single up/down control input
Output capability: standard
ICC category: MSI
GENERAL DESCRIPTION
The 74HC/HCT191 are high-speed Si-gate CMOS devices
and are pin compatible with low power Schottky TTL
(LSTTL). They are specified in compliance with JEDEC
standard no. 7A.
The 74HC/HCT191 are asynchronously presettable 4-bit
binary up/down counters. They contain four master/slave
flip-flops with internal gating and steering logic to provide
asynchronous preset and synchronous count-up and
count-down operation.
Asynchronous parallel load capability permits the counter
to be preset to any desired number. Information present on
the parallel data inputs (D0 to D3) is loaded into the counter
and appears on the outputs when the parallel load (PL)
input is LOW. As indicated in the function table, this
operation overrides the counting function.
Counting is inhibited by a HIGH level on the count enable
(CE) input. When CE is LOW internal state changes are
initiated synchronously by the LOW-to-HIGH transition of
the clock input. The up/down (U/D) input signal determines
the direction of counting as indicated in the function table.
The CE input may go LOW when the clock is in either
state, however, the LOW-to-HIGH CE transition must
occur only when the clock is HIGH. Also, the U/D input
should be changed only when either CE or CP is HIGH.
Overflow/underflow indications are provided by two types
of outputs, the terminal count (TC) and ripple clock (RC).
The TC output is normally LOW and goes HIGH when a
circuit reaches zero in the count-down mode or reaches
“15” in the count-up-mode. The TC output will remain
HIGH until a state change occurs, either by counting or
presetting, or until U/D is changed. Do not use the TC
output as a clock signal because it is subject to decoding
spikes. The TC signal is used internally to enable the
RC output. When TC is HIGH and CE is LOW, the RC
output follows the clock pulse (CP). This feature simplifies
the design of multistage counters as shown in Figs 5
and 6.
In Fig.5, each RC output is used as the clock input to the
next higher stage. It is only necessary to inhibit the first
stage to prevent counting in all stages, since a HIGH on
CE inhibits the RC output pulse as indicated in the function
table. The timing skew between state changes in the first
and last stages is represented by the cumulative delay of
the clock as it ripples through the preceding stages. This
can be a disadvantage of this configuration in some
applications.
Fig.6 shows a method of causing state changes to occur
simultaneously in all stages. The RC outputs propagate
the carry/borrow signals in ripple fashion and all clock
inputs are driven in parallel. In this configuration the
duration of the clock LOW state must be long enough to
allow the negative-going edge of the carry/borrow signal to
ripple through to the last stage before the clock goes
HIGH. Since the RC output of any package goes HIGH
shortly after its CP input goes HIGH there is no such
restriction on the HIGH-state duration of the clock.
In Fig.7, the configuration shown avoids ripple delays and
their associated restrictions. Combining the TC signals
from all the preceding stages forms the CE input for a
given stage. An enable must be included in each carry
gate in order to inhibit counting. The TC output of a given
stage it not affected by its own CE signal therefore the
simple inhibit scheme of Figs 5 and 6 does not apply.
相关PDF资料 |
PDF描述 |
|---|---|
| 74LCX245SJ | IC TRANSCVR BIDIR 8BIT 20SOP |
| 74LVTH2244MTC | IC BUFF/DVR TRI-ST DUAL 20TSSOP |
| 74HC93DB,118 | IC 4BIT BINARY RIPPLE 14SSOP |
| 74LVT2244MTC | IC BUFF/DVR TRI-ST DUAL 20TSSOP |
| 74HCT4060DB,118 | IC 14STAGE BINARY RIPPLE 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74HC191DB-T | 功能描述:计数器 IC SYNC BIN U/D COUNTER RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
| 74HC191D-T | 功能描述:计数器 IC SYNC BIN U/D COUNTER RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
| 74HC191E | 制造商:undefined 功能描述: |
| 74HC191N | 制造商:NXP Semiconductors 功能描述:HC Counter Bulk 制造商:NXP Semiconductors 功能描述:IC 74HC CMOS 74HC191 DIP16 5V 制造商:NXP Semiconductors 功能描述:IC, 74HC CMOS, 74HC191, DIP16, 5V 制造商:NXP Semiconductors 功能描述:BINARY COUNTER, 4BIT, UP/DOWN, DIP-16; Counter Type:Presettable Binary, Synchronous, Up / Down; Clock Frequency:39MHz; Count Maximum:15; Supply Voltage Min:2V; Supply Voltage Max:6V; Logic Case Style:DIP; No. of Pins:16 ;RoHS Compliant: Yes 制造商:NXP Semiconductors 功能描述:4-bit binary up/down counter,74HC191N 制造商:NXP Semiconductors 功能描述:Counter Single 4-Bit Sync Binary UP/Down 16-Pin PDIP Bulk |
| 74HC191N,652 | 功能描述:计数器 IC COUNTER UP/DOWN SYNC RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。