- 您现在的位置：买卖IC网 > PDF目录8097 > 74HCT4059D,118 (NXP Semiconductors)IC PROG DIVIDE-BY-N COUNT 24SOIC PDF资料下载
参数资料
| 型号： | 74HCT4059D,118 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC PROG DIVIDE-BY-N COUNT 24SOIC |
| 产品培训模块： | Logic Packages |
| 标准包装： | 1,000 |
| 系列： | 74HCT |
| 逻辑类型： | 除以 N |
| 方向： | 下 |
| 元件数： | 1 |
| 每个元件的位元数： | 16 |
| 复位： | 异步 |
| 计时： | 同步 |
| 计数速率： | 36MHz |
| 触发器类型： | 正边沿 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SO |
| 包装： | 带卷 (TR) |
| 其它名称： | 74HCT4059D-T 74HCT4059D-T-ND 933757430118 |
1998 Jul 08
19
Philips Semiconductors
Product specication
Programmable divide-by-n counter
74HC/HCT4059
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
DIP
SOLDERING BY DIPPING OR BY WAVE
The maximum permissible temperature of the solder is
260
°C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
REPAIRING SOLDERED JOINTS
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300
°C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400
°C, contact may be up to 5 seconds.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°C.
WAVE SOLDERING
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
The longitudinal axis of the package footprint must be
parallel to the solder flow.
The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°C within
6 seconds. Typical dwell time is 4 seconds at 250
°C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°C.
相关PDF资料 |
PDF描述 |
|---|---|
| 74LV4020D,112 | IC 14BIT BINARY RIPPLE 16-SOIC |
| 74LV4020D,118 | IC 14STAGE BINARY RIPPLE 16SOIC |
| 74LV4020PW,112 | IC 14BIT BINARY RIPPLE 16-TSSOP |
| 74HCT4040DB,118 | IC 12STAGE BIANRY RIPPLE 16SSOP |
| OSTVH045152 | TERM BLOCK PLUG 5.08MM 4POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74HCT4059D-T | 功能描述:计数器 IC PROGRMBL DIVIDE-BY-N COUNTER RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
| 74HCT4059N,112 | 功能描述:计数器 IC COUNTR PROG DIV-BY-N DIV X N RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
| 74HCT4060BQ | 制造商:NXP Semiconductors 功能描述:IC 14 STAGE RIP COUNT DHVQF |
| 74HCT4060BQ,115 | 功能描述:计数器 IC Counter Single 14Bit Binary UP T/R RoHS:否 制造商:NXP Semiconductors 计数器类型:Binary Counters 逻辑系列:74LV 位数:10 计数法: 计数顺序: 工作电源电压:1 V to 5.5 V 工作温度范围:- 40 C to + 125 C 封装 / 箱体:SOT-109 封装:Reel |
| 74HCT4060BQ-Q100,1 | 制造商:NXP Semiconductors 功能描述:Counter Single 14-Bit Binary UP 16-Pin DHVQFN EP T/R 制造商:NXP Semiconductors 功能描述:74HCT4060BQ-Q100/DHVQFN16/REEL - Tape and Reel 制造商:NXP Semiconductors 功能描述:IC BINARY RIPPLE COUNT 16DHVQFN |
发布紧急采购，3分钟左右您将得到回复。