- 您现在的位置：买卖IC网 > PDF目录222840 > 74VHC123AM (FAIRCHILD SEMICONDUCTOR CORP) Dual Retriggerable Monostable Multivibrator PDF资料下载
参数资料
| 型号： | 74VHC123AM |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | 谐振器 |
| 英文描述： | Dual Retriggerable Monostable Multivibrator |
| 中文描述： | AHC/VHC SERIES, DUAL MONOSTABLE MULTIVIBRATOR, PDSO16 |
| 封装： | 0.150 INCH, MS-012, SOIC-16 |
| 文件页数： | 10/14页 |
| 文件大小： | 464K |
| 代理商： | 74VHC123AM |
74VHC123A
Dual
Retrig
g
erab
le
Monostab
le
Multivibrator
1993 Fairchild Semiconductor Corporation
www.fairchildsemi.com
74VHC123A Rev. 1.2
5
Functional Description
1. Stand-by State
The external capacitor (Cx) is fully charged to VCC in
the Stand-by State. That means, before triggering,
the QP and QN transistors which are connected to the
Rx/Cx node are in the off state. Two comparators that
relate to the timing of the output pulse, and two refer-
ence voltage supplies turn off. The total supply cur-
rent is only leakage current.
2. Trigger Operation
Trigger operation is effective in any of the following
three cases. First, the condition where the A input is
LOW, and B input has a rising signal; second, where
the B input is HIGH, and the A input has a falling sig-
nal; and third, where the A input is LOW and the B
input is HIGH, and the CLR input has a rising signal.
After a trigger becomes effective, comparators C1
and C2 start operating, and QN is turned on. The
external capacitor discharges through QN. The volt-
age level at the Rx/Cx node drops. If the Rx/Cx volt-
age level falls to the internal reference voltage VrefL,
the output of C1 becomes LOW. The flip-flop is then
reset and QN turns off. At that moment C1 stops but
C2 continues operating.
After QN turns off, the voltage at the Rx/Cx node
starts rising at a rate determined by the time constant
of external capacitor Cx and resistor Rx.
Upon triggering, output Q becomes HIGH, following
some delay time of the internal F/F and gates. It stays
HIGH even if the voltage of Rx/Cx changes from fall-
ing to rising. When Rx/Cx reaches the internal refer-
ence voltage VrefH, the output of C2 becomes LOW,
the output Q goes LOW and C2 stops its operation.
That means, after triggering, when the voltage level
of the Rx/Cx node reaches VrefH, the IC returns to its
MONOSTABLE state.
With large values of Cx and Rx, and ignoring the dis-
charge time of the capacitor and internal delays of
the IC, the width of the output pulse, tW (OUT), is as
follows:
tW (OUT) = 1.0 Cx Rx
3. Retrigger operation (74VHC123A)
When a new trigger is applied to either input A or B
while in the MONOSTABLE state, it is effective only if
the IC is charging Cx. The voltage level of the Rx/Cx
node then falls to VrefL level again. Therefore the Q
output stays HIGH if the next trigger comes in before
the time period set by Cx and Rx.
If the new trigger is very close to a previous trigger,
such as an occurrence during the discharge cycle, it
will have no effect.
The minimum time for a trigger to be effective 2nd
trigger, tRR (Min), depends on VCC and Cx.
4. Reset Operation
In normal operation, the CLR input is held HIGH. If
CLR is LOW, a trigger has no affect because the Q
output is held LOW and the trigger control F/F is
reset. Also, Qp turns on and Cx is charged rapidly to
VCC.
This means if CLR is set LOW, the IC goes into a wait
state.
相关PDF资料 |
PDF描述 |
|---|---|
| 74VHC123AMTC | Automotive Catalog Dual D-Type Positive-Edge-Triggered Flip-Flops With Clear and Preset 14-TSSOP -40 to 125 |
| 74VHC123AN | Dual Retriggerable Monostable Multivibrator |
| 74VHC123A | Automotive Catalog Dual D-Type Positive-Edge-Triggered Flip-Flops With Clear and Preset 14-SOIC -40 to 125 |
| 74VHC132NX | Quad 2-Input NAND Schmitt Trigger |
| 74VHC132SJ | Quadruple 2-Input Exclusive-OR Gates 14-TSSOP -40 to 85 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 74VHC123AM | 制造商:Fairchild Semiconductor Corporation 功能描述:74VHC CMOS SMD 74VHC123 SOIC16 |
| 74VHC123AM_Q | 功能描述:单稳态多谐振荡器 Dual Multivibrator RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| 74VHC123AMTC | 功能描述:单稳态多谐振荡器 Dual Multivibrator RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| 74VHC123AMTC_NL | 功能描述:单稳态多谐振荡器 FINISHED GOOD RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| 74VHC123AMTC_Q | 功能描述:单稳态多谐振荡器 Dual Multivibrator RoHS:否 制造商:Texas Instruments 每芯片元件:1 逻辑系列:LVC 逻辑类型:Monostable Multivibrator 封装 / 箱体:SSOP-8 传播延迟时间:18.6 ns 高电平输出电流:- 32 mA 低电平输出电流:32 mA 电源电压-最大:5.5 V 电源电压-最小:1.65 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。