780964 PDF资料下载(12/129 页)Common to 78K/0 Series

参数资料

User's Manual U12326EJ4V0UM

CHAPTER 1 MEMORY SPACE

1.1 Memory Spaces

The 78K/0 Series product program memory map varies depending on the internal memory capacity. For details

of memory-mapped address area, refer to the user’s manual of each product.

1.2 Internal Program Memory (Internal ROM) Space

Each 78K/0 Series product has internal ROM in the address space. Program and table data, etc. are stored

in the ROM. Normally, this memory space is addressed by the program counter (PC). For details of the internal

ROM space, refer to the user’s manual of each product.

1.3 Vector Table Area

The 64-byte area 0000H to 003FH is reserved as a vector table area. The program start addresses for branch

upon RESET input or interrupt request generation are stored in the vector table area. Of the 16-bit address, the

lower 8 bits are stored at even addresses and the higher 8 bits are stored at odd addresses. For the vector table

area, refer to the user’s manual of each product.

1.4 CALLT Instruction Table Area

The 64-byte area 0040H to 007FH can store the subroutine entry address of a 1-byte call instruction (CALLT).

1.5 CALLF Instruction Entry Area

The 2048-byte area 0800H to 0FFFH can perform a direct subroutine call with a 2-byte call instruction (CALLF).

1.6 Internal Data Memory (Internal RAM) Space

78K/0 Series products incorporate the following RAMs. For details of these RAMs, refer to the user’s manual

of each product.

(1) Internal high-speed RAM

Each 78K/0 Series product incorporates an internal high-speed RAM. In the 32-byte area FEE0H to FEFFH

of these areas, 4 banks of general-purpose registers, each bank consisting of eight 8-bit registers, are

allocated.

The internal high-speed RAM can also be used as a stack memory.

(2) Buffer RAM

There are some products in the 78K/0 Series to which buffer RAM is allocated. This RAM is used to store

the transfer/receive data of serial interface channel 1 (3-wire serial I/O mode with automatic transfer/receive

function). If not used in this mode, the buffer RAM can also be used as an ordinary RAM area.

相关代理商/技术参数	参数描述
78097-002	功能描述:I/O 连接器 2X3 PCB Receptacle, Low Profile, Right Angle RoHS:否制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角:
78097-002LF	制造商:FCI 功能描述:Conn Shrouded Header HDR 6 POS Solder RA Thru-Hole Tray 制造商:FCI 功能描述:CONN SHRD HDR HDR 6 POS SLDR RA TH - Trays
78097-004	功能描述:I/O 连接器 2X3 PCB Receptacle, Low Profile, Right Angle RoHS:否制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角:
78097-004LF	功能描述:I/O 连接器 2X3 PCB Receptacle, Low Profile, Right Angle RoHS:否制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角:
78097-007	功能描述:I/O 连接器 2X3 PCB Receptacle, Low Profile, Right Angle RoHS:否制造商:Hirose Connector 产品:Plugs 系列:DH 端口数量: 位置/触点数量:51 节距:1 mm 触点电镀: 触点材料: 型式:Male 电流额定值:0.5 A 安装风格:Cable 端接类型:IDC 颜色: 安装角:

发布紧急采购，3分钟左右您将得到回复。

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购