参数资料
型号: 78M6618-IMR/F/P
厂商: TERIDIAN SEMICONDUCTOR CORP
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, QCC68
封装: ROHS COMPLIANT, QFN-68
文件页数: 21/32页
文件大小: 374K
代理商: 78M6618-IMR/F/P
78M6618 Data Sheet
DS_6618_005
28
Rev. 1.3
4.3
Digital Pins
Table 28: Digital Pins
Name
Type Circuit
Description
COM1,COM0
O
5
LCD Common Outputs: These 2 pins provide the select signals for an
LCD display.
DIO3
I/O
3,4
Dedicated DIO pin.
SEG0…SEG2,
SEG7, SEG8
SEG12,
SEG14…SEG18
O
5
Dedicated LCD Segment Output pins.
SEG24/DIO4…
SEG31/DIO11,
SEG33/DIO13…
SEG39/DIO19,
SEG63/DIO43
I/O
3, 4, 5
Multi-use pins, configurable as either LCD SEG driver or DIO.
(DIO4 = SCK, DIO5 = SDA when configured as EEPROM interface;
WPULSE = DIO6, VARPULSE = DIO7 when configured as pulse
outputs). If unused, these pins must be configured as DIOs and
set to outputs by the firmware.
SEG3/PCLK
SEG4/PSDO
SEG5/PCSZ
SEG6/PSDI
I/O
3, 4, 5
Multi-use pins, configurable as either LCD SEG driver or SPI PORT.
E_RXTX/SEG9
I/O
1, 4, 5
Multi-use pins, configurable as either emulator port pins (when ICE_E
pulled high) or LCD SEG drivers (when ICE_E tied to GND).
E_RST/SEG11
I/O
1, 4, 5
E_TCLK/SEG10
O
4, 5
ICE_E
I
2
ICE enable. When zero, E_RST, E_TCLK and E_RXTX become
SEG32, SEG33 and SEG38 respectively. For production units, this
pin should be pulled to GND to disable the emulator port.
CKTEST/SEG19,
MUXSYNC/SEG7
O
4, 5
Multi-use pins, configurable as either multiplexer/clock output or LCD
segment driver using the I/O RAM registers CKOUT_E or
MUX_SYNC_E.
TMUXOUT
O
4
Digital output test multiplexer. Controlled by TMUX[3:0].
OPT_RX/DIO1
I/O
3, 4, 7
Multi-use pin, configurable as Optical Receive Input or general DIO.
When configured as OPT_RX, this pin receives a signal from an external
photo-detector used in an IR serial interface. If unused, this pin must
be terminated to V3P3D or GNDD, or configured as a DIO and set
to an output by the firmware.
OPT_TX/DIO2
I/O
3, 4
Multi-use pin, configurable as either optical LED transmit output,
WPULSE, RPULSE, or general DIO. When configured as OPT_TX,
this pin is capable of directly driving an LED for transmitting data in
an IR serial interface. If unused, this pin must be left open, or
configured as a DIO and set to an output by the firmware.
RESET
I
2
Chip reset: This input pin is used to reset the chip into a known state.
For normal operation, this pin is pulled low. To reset the chip, this pin
should be pulled high. This pin has an internal 30
A (nominal)
current source pull-down. No external reset circuitry is necessary.
RX
I
3
UART input. If this pin is unused, it must be terminated to V3P3D
or GNDD.
TX
O
4
UART output.
TEST
I
7
Enables Production Test. This pin must be grounded in normal
operation.
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output.
The circuit number denotes the equivalent circuit, as specified in Section 5 I/O Equivalent Circuits.
相关PDF资料
PDF描述
78M6618-IMR/F SPECIALTY ANALOG CIRCUIT, QCC68
78M6618-IM/F SPECIALTY ANALOG CIRCUIT, QCC68
78M6618-IM/F/P SPECIALTY ANALOG CIRCUIT, QCC68
78M6618-IMR/F/P SPECIALTY ANALOG CIRCUIT, QCC68
7MBP150RTJ060 AC MOTOR CONTROLLER, 300 A, XMA25
相关代理商/技术参数
参数描述
78M6618-M/F/P1 功能描述:计量片上系统 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
78M6618-M/F/P2 功能描述:IC PWR MEASUREMENT OCTAL 68QFN 制造商:maxim integrated 系列:- 包装:管件 零件状态:停产 输入阻抗:40 千欧 ~ 90 千欧 测量误差:0.5% 电压 - I/O 高:2V 电压 - I/O 低:0.8V 电流 - 电源:- 电压 - 电源:3 V ~ 3.6 V 表计类型:单相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:68-VFQFN 裸露焊盘 供应商器件封装:68-QFN(8x8) 标准包装:260
78M6618-MR/F/P1 功能描述:计量片上系统 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
78M6618-MR/F/P2 功能描述:IC PWR MEASUREMENT OCTAL 68QFN 制造商:maxim integrated 系列:- 包装:带卷(TR) 零件状态:停产 输入阻抗:40 千欧 ~ 90 千欧 测量误差:0.5% 电压 - I/O 高:2V 电压 - I/O 低:0.8V 电流 - 电源:- 电压 - 电源:3 V ~ 3.6 V 表计类型:单相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:68-VFQFN 裸露焊盘 供应商器件封装:68-QFN(8x8) 标准包装:2,500
78M6618-PDU1 功能描述:BOARD EVAL 78M6618 PDU1 RoHS:是 类别:编程器,开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理,电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板