参数资料
型号: 78M6618-IMR/F/P
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, QCC68
封装: 8 X 8 MM, ROHS COMPLIANT, TQFN-68
文件页数: 21/32页
文件大小: 419K
代理商: 78M6618-IMR/F/P
78M6618 Data Sheet
DS_6618_005
28
Rev. 1.4
4.3
Digital Pins
Table 28: Digital Pins
Name
Type Circuit
Description
COM1,COM0
O
5
LCD Common Outputs: These 2 pins provide the select signals for an
LCD display.
DIO3
I/O
3,4
Dedicated DIO pin.
SEG0…SEG2,
SEG7, SEG8
SEG12,
SEG14…SEG18
O
5
Dedicated LCD Segment Output pins.
SEG24/DIO4…
SEG31/DIO11,
SEG33/DIO13…
SEG39/DIO19,
SEG63/DIO43
I/O
3, 4, 5
Multi-use pins, configurable as either LCD SEG driver or DIO.
(DIO4 = SCK, DIO5 = SDA when configured as EEPROM interface;
WPULSE = DIO6, VARPULSE = DIO7 when configured as pulse
outputs). If unused, these pins must be configured as DIOs and
set to outputs by the firmware.
SEG3/PCLK
SEG4/PSDO
SEG5/PCSZ
SEG6/PSDI
I/O
3, 4, 5
Multi-use pins, configurable as either LCD SEG driver or SPI PORT.
E_RXTX/SEG9
I/O
1, 4, 5
Multi-use pins, configurable as either emulator port pins (when ICE_E
pulled high) or LCD SEG drivers (when ICE_E tied to GND).
E_RST/SEG11
I/O
1, 4, 5
E_TCLK/SEG10
O
4, 5
ICE_E
I
2
ICE enable. When zero, E_RST, E_TCLK and E_RXTX become
SEG32, SEG33 and SEG38 respectively. For production units, this
pin should be pulled to GND to disable the emulator port.
CKTEST/SEG19,
MUXSYNC/SEG7
O
4, 5
Multi-use pins, configurable as either multiplexer/clock output or LCD
segment driver using the I/O RAM registers CKOUT_E or
MUX_SYNC_E.
TMUXOUT
O
4
Digital output test multiplexer. Controlled by TMUX[3:0].
OPT_RX/DIO1
I/O
3, 4, 7
Multi-use pin, configurable as Optical Receive Input or general DIO.
When configured as OPT_RX, this pin receives a signal from an external
photo-detector used in an IR serial interface. If unused, this pin must
be terminated to V3P3D or GNDD, or configured as a DIO and set
to an output by the firmware.
OPT_TX/DIO2
I/O
3, 4
Multi-use pin, configurable as either optical LED transmit output,
WPULSE, RPULSE, or general DIO. When configured as OPT_TX,
this pin is capable of directly driving an LED for transmitting data in
an IR serial interface. If unused, this pin must be left open, or
configured as a DIO and set to an output by the firmware.
RESET
I
2
Chip reset: This input pin is used to reset the chip into a known state.
For normal operation, this pin is pulled low. To reset the chip, this pin
should be pulled high. This pin has an internal 30
A (nominal)
current source pull-down. No external reset circuitry is necessary.
RX
I
3
UART input. If this pin is unused, it must be terminated to V3P3D
or GNDD.
TX
O
4
UART output.
TEST
I
7
Enables Production Test. This pin must be grounded in normal
operation.
Pin types: P = Power, O = Output, I = Input, I/O = Input/Output.
The circuit number denotes the equivalent circuit, as specified in Section 5 I/O Equivalent Circuits.
相关PDF资料
PDF描述
7MBP150RTJ060 AC MOTOR CONTROLLER, 300 A, XMA25
7MBP25RU2A120 AC MOTOR CONTROLLER, 50 A, XMA22
7MBP50RTJ060 AC MOTOR CONTROLLER, 100 A, XMA25
7MBP50RU2A120 AC MOTOR CONTROLLER, 100 A, XMA22
7MBP75RU2A120 AC MOTOR CONTROLLER, 150 A, XMA22
相关代理商/技术参数
参数描述
78M6618-M/F/P1 功能描述:计量片上系统 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
78M6618-M/F/P2 功能描述:IC PWR MEASUREMENT OCTAL 68QFN 制造商:maxim integrated 系列:- 包装:管件 零件状态:停产 输入阻抗:40 千欧 ~ 90 千欧 测量误差:0.5% 电压 - I/O 高:2V 电压 - I/O 低:0.8V 电流 - 电源:- 电压 - 电源:3 V ~ 3.6 V 表计类型:单相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:68-VFQFN 裸露焊盘 供应商器件封装:68-QFN(8x8) 标准包装:260
78M6618-MR/F/P1 功能描述:计量片上系统 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
78M6618-MR/F/P2 功能描述:IC PWR MEASUREMENT OCTAL 68QFN 制造商:maxim integrated 系列:- 包装:带卷(TR) 零件状态:停产 输入阻抗:40 千欧 ~ 90 千欧 测量误差:0.5% 电压 - I/O 高:2V 电压 - I/O 低:0.8V 电流 - 电源:- 电压 - 电源:3 V ~ 3.6 V 表计类型:单相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:68-VFQFN 裸露焊盘 供应商器件封装:68-QFN(8x8) 标准包装:2,500
78M6618-PDU1 功能描述:BOARD EVAL 78M6618 PDU1 RoHS:是 类别:编程器,开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理,电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板