- 您现在的位置：买卖IC网 > PDF目录20604 > 78M6618-IMR/F (Maxim Integrated)IC PWR MEASUREMENT OCTAL 68-QFN PDF资料下载
参数资料
| 型号： | 78M6618-IMR/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/32页 |
| 文件大小： | 0K |
| 描述： | IC PWR MEASUREMENT OCTAL 68-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
78M6618 Data Sheet
DS_6618_005
1.12 Real-Time Clock (RTC)
The RTC circuit is driven directly by the crystal oscillator. The RTC consists of a counter chain and output
registers. The counter chain consists of registers for seconds, minutes, hours, day of week, day of
month, month, and year (including leap years). See the 78M6618 Programmer’s Reference Manual for
more information regarding the use of the 78M6618 RTC.
1.13 Hardware Watchdog Timer
V1
In addition to the basic watchdog timer included in the 80515 MPU, an
independent, robust, fixed-duration, watchdog timer (WDT) is included in
V3P3
V3P3 - 10mV
WDT dis-
abled
the device. It uses the crystal oscillator as its time base and must be
refreshed by the MPU firmware at least every 1.5 seconds. When not
V3P3 -
400mV
VBIAS
Normal
operation,
WDT
enabled
Battery
modes
refreshed on time the WDT overflows, and the part is reset as if the RESET
pin were pulled high, except that the IORAM bits will be maintained. 4096
oscillator cycles (or 125 ms) after the WDT overflow, the MPU will be
launched from program address 0x0000. Asserting ICE_E will deactivate
the WDT.
The WDT can also be disabled by tying the V1 pin to V3P3. This also
deactivates V1 power fault detection. Since there is no method in firmware
to disable the crystal oscillator or the WDT, it is guaranteed that whatever
state the part might find itself in, upon watchdog overflow, the part will be
reset to a known state.
0V
Figure 3: Functions Defined by V1
1.14 Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap re-
ference. The primary use of the temperature data is to determine the magnitude of compensation required
to offset the thermal drift in the system. See the 78M6618 Programmer’s Reference Manual for more
information regarding the use of the 78M6618 Temperature Sensor.
1.15 General Purpose Digital I/O
The 78M6618 includes up to 19 pins of general-purpose digital I/O. When configured as inputs, these
pins are 5V compatible (no current-limiting resistors are needed). On reset or power-up, all DIO pins are
inputs until they are configured for the desired direction under MPU control. The Digital I/O pins can be
categorized as follows:
?
?
DIO1/OPT_RX, DIO2/OPT_TX
DIO3
(2
(1
pins)
pin )
UART/DIO pin
Dedicated DIO pin
?
DIO4/SEG24
-- DIO11/SEG31
(8
pins)
LCD/DIO pins
?
?
DIO13/SEG33 -- DIO19/SEG39
DIO43/SEG63
(7
(1
pins)
pin )
LCD/DIO pins
LCD/DIO pin
10
Rev. 1.4
相关PDF资料 |
PDF描述 |
|---|---|
| R1S12-0509/H | CONV DC/DC 1W 05VIN 09VOUT |
| VI-BNT-EU-F1 | CONVERTER MOD DC/DC 6.5V 200W |
| F931C336KCC | CAP TANT 33UF 16V 10% 2312 |
| RCD-24-0.70/W/X1 | LED DRIVER CONST .7A 2-35VOUT |
| VLCF5020T-220MR75-1 | INDUCTOR POWER 22UH .75A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 78M6618-M/F/P1 | 功能描述:计量片上系统 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 78M6618-M/F/P2 | 功能描述:IC PWR MEASUREMENT OCTAL 68QFN 制造商:maxim integrated 系列:- 包装:管件 零件状态:停产 输入阻抗:40 千欧 ~ 90 千欧 测量误差:0.5% 电压 - I/O 高:2V 电压 - I/O 低:0.8V 电流 - 电源:- 电压 - 电源:3 V ~ 3.6 V 表计类型:单相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:68-VFQFN 裸露焊盘 供应商器件封装:68-QFN（8x8） 标准包装:260 |
| 78M6618-MR/F/P1 | 功能描述:计量片上系统 - SoC 8 Out Sgl Phase Pwr & Energy Msrmt IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 78M6618-MR/F/P2 | 功能描述:IC PWR MEASUREMENT OCTAL 68QFN 制造商:maxim integrated 系列:- 包装:带卷（TR） 零件状态:停产 输入阻抗:40 千欧 ~ 90 千欧 测量误差:0.5% 电压 - I/O 高:2V 电压 - I/O 低:0.8V 电流 - 电源:- 电压 - 电源:3 V ~ 3.6 V 表计类型:单相 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:68-VFQFN 裸露焊盘 供应商器件封装:68-QFN（8x8） 标准包装:2,500 |
| 78M6618-PDU1 | 功能描述:BOARD EVAL 78M6618 PDU1 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。