- 您现在的位置：买卖IC网 > PDF目录16278 > 78Q2133-DB (Maxim Integrated Products)EVAL BOARD 78Q2133 PDF资料下载
参数资料
| 型号： | 78Q2133-DB |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/38页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD 78Q2133 |
| 标准包装： | 1 |
| 系列： | * |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
78Q2123/78Q2133 Data Sheet
DS_21x3_001
10
Rev. 1.6
1.6
Additional Features
1.6.1
LED Indicators
There are two LED pins that can be used to indicate various states of operation of the
78Q2123/78Q2133. The function of these pins is programmable via the MR23 register as shown in the
table below:
LED State Indication
0
1 = Link OK (Default LED0)
1
1 = RX or TX Activity (Default LED1)
2
1 = TX Activity
3
1 = RX Activity
4
1 = Collision
5
1 = 100 BASE-TX mode
6
1 = 10 BASE-T mode
7
1 = Full Duplex
8
1= Link OK & Blink = RX or TX Activity
The default status of these LEDs are “Link OK” for LED0 and “RX or TX Activity” for LED1.
1.6.2
Interrupt Pin
The 78Q2123 and 78Q2133 have an Interrupt pin (INTR) that is asserted whenever any of the eight
interrupt bits of MR17.7:0 are set. These interrupt bits can be disabled via the MR17.15:8 Interrupt
Enable bits. The Interrupt Polarity bit, MR16.14, controls the active level of the INTR pin. When the INTR
pin is not asserted, the pin is held in a high impedance state. An external pull-up or pull-down resistor may
be required for use with the INTR pin.
1.6.3
Automatic MDI/ MDI-X Configuration
The 78Q2123 and 78Q2133 implement the automatic MDI/MDI-X configuration detailed in IEEE-802.3
2002. This function eliminates the need for cross over cables when connecting to another device. When
auto-switching is enabled, the 78Q2123/78Q2133 will attempt to detect activity on its given configuration.
If no activity is seen for 60 ms, the device will switch to the other configuration depending on a random
number sequence. The initial seed of the random number generator can be set via MR24.3:0. In
addition, the part includes an asynchronous MDIX reset that varies from 1.29 seconds to 1.57 seconds to
ensure lock step will not occur between two devices.
The 78Q2123 and 78Q2133 will also allow for auto-switching while the part is not in auto-negotiation
mode. The IEEE 802.3 specification will not work in this case if the other device is in auto-negotiation
mode. The 78Q2123 and 78Q2133 default to auto MDIX enabled with parallel detection. Register bits
MR24.6 and MR24.7 are both defaulted to 1. The 78Q2123 and 78Q2133 will resolve the proper
configuration within 5 seconds.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX14821EVKIT# | EVAL KIT MAX14821 |
| UVZ1C472MHD | CAP ALUM 4700UF 16V 20% RADIAL |
| 78Q2123-DB | BOARD DEMO 78Q2123 78Q2133 |
| 78Q2120C09-DB | BOARD DEMO 78Q2120C |
| NCP301LSN45T1G | IC DETECTOR VOLTAGE 4.5V 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 78Q2133-DIE | 制造商:Maxim Integrated Products 功能描述:78Q2133-DIE NOTE: MOQ = 10500 DIE (1 WAFER) - Gel-pak, waffle pack, wafer, diced wafer on film |
| 78Q2133R/F | 功能描述:以太网 IC 10/100 Fast Ethernet MicroPHY RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| 78Q2133R/F1 | 功能描述:以太网 IC RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| 78Q2133S/F | 功能描述:1/1 Transceiver Full Ethernet 32-TQFN (5x5) 制造商:maxim integrated 系列:- 包装:管件 零件状态:有效 类型:收发器 协议:以太网 驱动器/接收器数:1/1 双工:全 接收器滞后:- 数据速率:- 电压 - 电源:3.3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘 供应商器件封装:32-TQFN（5x5） 标准包装:490 |
| 78Q2133SR/F | 功能描述:1/1 Transceiver Full Ethernet 32-TQFN (5x5) 制造商:maxim integrated 系列:- 包装:带卷（TR） 零件状态:有效 类型:收发器 协议:以太网 驱动器/接收器数:1/1 双工:全 接收器滞后:- 数据速率:- 电压 - 电源:3.3V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:32-WFQFN 裸露焊盘 供应商器件封装:32-TQFN（5x5） 标准包装:2,500 |
发布紧急采购，3分钟左右您将得到回复。