参数资料
型号: 7X11-5-8815
厂商: 3M (TC)
文件页数: 6/8页
文件大小: 0K
描述: TAPE ADHESIVE TRANSFER 7X11"
MSDS 材料安全数据表: 8805,8810,8815,8820 MSDS
标准包装: 5
系列: 8815
胶带类型: 胶粘传输带
胶合剂: 压敏胶合剂(PSA)
背衬,载体: 聚合物
厚度: 0.0150"(15.0 mils,0.381mm)
宽: 7.00"(177.80mm)
长度: 11.00"(279.40mm)
颜色:
使用: 热导电
包装: 散装
其它名称: 3M10309
3M ? Thermally Conductive Adhesive Transfer Tapes
8805 ? 8810 ? 8815 ? 8820
Application Guidelines (continued)
5.) Application Tips:
? For rigid to rigid bonding, a twisting motion during assembly of the substrates will improve wetting. This should be a
back and forth twisting motion during the application of compression.
? For flexible to rigid or flexible to flexible bonding, a roll lamination system may be employed to apply the flexible
substrate down to the rigid (or other flexible) substrate. Rubber nip rollers, heated steel rollers, and other methods can
be employed to bond in a continuous manner.
? Heat can be employed to increase wetting percentage and wetting rate of the substrates and to build room temperature
bond strength.
? Primers may be employed to increase adhesion to low surface energy substrates (eg. plastic packages). Contact your
3M Technical Service Representative for more information about primers.
? For best product performance, it is important to use pressure and time conditions to achieve as much wetting as
possible.
6.) Rework Tips:
? Rework requires separation of the two substrates. Separation can be accomplished by any practical means: prying,
torquing or peeling. The tape will be destroyed upon separation and must be replaced. The surfaces should be re-
cleaned according to the recommendations in this data page.
? Heating up the substrates can reduce the adhesion level and make removal easier.
? Part separation can be aided by immersion in warm water. This should eventually reduce the adhesion and make
prying, torquing or peeling apart the substrates easier.
(6)
相关PDF资料
PDF描述
4-641200-0 10P MTA100 CONN ASSY BLU LF
TQ2SS-L2-12V RELAY TELECOM DPDT 2A 12V
4-641198-0 10P MTA100 CONN ASSY RED LF
TXD2-12V RELAY GEN PURPOSE DPDT 2A 12V
4-641193-0 10P MTA100 CONN ASSY GRN LF
相关代理商/技术参数
参数描述
7X-12.000MBA-T 功能描述:标准时钟振荡器 9 12.000MHz 3.3V25ppm(-10 +70C) RoHS:否 制造商:AVX 产品:Standard Clock Oscillators 封装 / 箱体:7 mm x 5 mm 频率:75 MHz 频率稳定性:50 PPM 电源电压:2.5 V 负载电容: 端接类型:SMD/SMT 最小工作温度:0 C 最大工作温度:+ 70 C 输出格式:LVDS 尺寸: 封装:Reel 系列:
7X-12.000MBB-T 功能描述:标准时钟振荡器 9 12.000MHz 3.3V50ppm(-10 +70C) RoHS:否 制造商:AVX 产品:Standard Clock Oscillators 封装 / 箱体:7 mm x 5 mm 频率:75 MHz 频率稳定性:50 PPM 电源电压:2.5 V 负载电容: 端接类型:SMD/SMT 最小工作温度:0 C 最大工作温度:+ 70 C 输出格式:LVDS 尺寸: 封装:Reel 系列:
7X-12.000MBB-T 制造商:TXC Corporation 功能描述:OSCILLATOR CXO 12MHZ SMD
7X-12.000MBC-T 制造商:TXC Corporation 功能描述:OSCILLATOR XO 12MHZ 3.3V SMD 制造商:TXC Corporation 功能描述:3.2x2.5 CMOS Quartz Oscillator / Ceramic, 3.3V, +/-100ppm (-10 to 70C)
7X-12.000MBD-T 功能描述:12MHz CMOS XO (Standard) Oscillator Surface Mount 3.3V 15mA Enable/Disable 制造商:txc corporation 系列:7x 包装:带卷(TR) 零件状态:在售 类型:XO(标准) 频率:12MHz 功能:启用/禁用 输出:CMOS 电压 - 电源:3.3V 频率稳定度:±25ppm 工作温度:-40°C ~ 85°C 电流 - 电源(最大值):15mA 等级:- 安装类型:表面贴装 封装/外壳:4-SMD,无引线(DFN,LCC) 大小/尺寸:0.126" 长 x 0.098" 宽(3.20mm x 2.50mm) 高度 - 安装(最大值):0.043"(1.10mm) 电流 - 电源(禁用)(最大值):- 标准包装:3,000