参数资料
型号: 82AC2060
厂商: Grayhill Inc
文件页数: 4/6页
文件大小: 0K
描述: LEGEND SHEET DEADFRONT ON BLK
标准包装: 25
Modular Keyboards
ORIENTATION OF MODULES
A module, depending on circuitry, may not be
symmetrical. Rotating it 180° will result in a
different pin location. Please note the button
identification, the pin location for the desired
circuitry, and the direction of mounting. It is
important to use this information when designing
communicating with Grayhill. See Ordering
Information–Special Keyboard Modules on the
next page.
a printed circuit board layout and when
CIRCUIT DIAGRAMS
The bottom view of the line drawings shows
number (A1, A2, etc.) next to the pin locations
of each switch section. These pin numbers are
directly related to the circuit diagrams. For
SPST
Standard Modules
2PST 3PST
4PST
Lightable Modules
SPST 2PST
example, if the switch under Button A of a
standard module were SPST, the pins would
2
2
2
3
2
3
1
2
1
2
1
2
1
2
1
1
1
1
be located at the "#2" Position. If the module
3
4
3
4
3
4
3
4
4
4
were a lightable one with SPST circuitry, the
pins would be located at the "#1" Position. If
other locations are desired, specify them.
Coded Circuitry–To 7 Bits/Button
The coded circuits shown are suggested
C
C
C
C
C
C
possibilities and each button may carry a
different circuit. Location of active pins on
each button may be varied to conform with
layout of the printed circuit board. Up to a 7-bit
code is possible under each button.
Note: Coded switches are constructed so that common (C) is made after all other contacts.
Other Possible Circuit Configurations
Combinations of simple circuitries are also
C
C
C
C
possible as shown in the sample diagrams.
PRINTED CIRCUIT BOARD LAYOUT
This layout provides the horizontal printed circuit board layout as viewed from the top side of the
PC board. Turning end to end will result in a different pin location. However, the dimensional
relationship will remain the same.
Lightable Modules –per drawing below.
This drawing indicates the layout to be used for a 6 button module with light sources mounted two
ways: the lamps for the upper 3 buttons are mounted from the top or component side of the board,
and the lamps for the lower 3 buttons are mounted by the easy replacement method. (See also Light
Source and Lamp Mounting.) Light sources, when mounted from the top side of the board, must
be mounted before the keyboard modules; when mounted, lamp should extend no more than .250"
(6,35 mm) above the board.
Unlighted Module
Lightable Module
L
. 488 ± .003
(12,40 ± 0,08)
TYP.
.090
(2,29)
TYP.
.500 ± .003
(12,7 ± 0,76)
.687 ± .003
(17,45 ± 0,08)
.687 ± .003
(17,45 ± 0,08)
C
HOLE TO
ACCOMMODATE
.032 (0,81) DIA.
PIN
.045 ± .002
(1,14 ± 0,05)
TYP.
(8 PLACES)
.687 ± .003
(17,45 ± 0,08)
.112
± .003
(28,45
± 0,08)
TYP.
CL
DIMENSIONS ARE DEPENDENT ON
LAMP SOURCE. APPROXIMATELY
.020 (0,51) AND .100 (2,54) APART
FOR A T-1 LAMP OR LED
HOLE TO
ACCOMMODATE
.032 (0,81) DIA.
PIN
.170 (4,32)
RECOMMENDED
DIA. HOLE
ACCOMMODATES
LAMP IN EASY
REPLACEMENT
L
.094
± .010
C
.270 ± .003
MOUNTING
(2,39
(6,86 ± 0,08)
.687 ± .003
.687 ± .003
L
± 0,25)
C
.244 (6,20) TYP.
CL
(17,45 ± 0,08)
CL
(17,45 ± 0,08)
CL
Grayhill, Inc. ? 561 Hillgrove Avenue ? LaGrange, Illinois
60525-5997 ? USA ? Phone: 708-354-1040 ? Fax: 708-354-2820 ? www.grayhill.com
Keypads
43
相关PDF资料
PDF描述
3362S-1-202 TRIMMER 2K OHM 0.5W TH
W2H13C1048AT1F CAP FEEDTHRU .10UF 25V X7R 0805
3362S-1-201 TRIMMER 200 OHM 0.5W TH
W2A4YA120KAT2A CAP ARRAY 4CH 12PF 16V 0508
3362S-1-200 TRIMMER 20 OHM 0.5W TH
相关代理商/技术参数
参数描述
82-ADB1-C 制造商:Ideal Industries Inc 功能描述:LV KIT
82AF82 制造商:Switchcraft 功能描述:
82-B0101-1356 功能描述:RF 连接器 CONNECTOR ASSEMBLY RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型:
82-B0202-2218 功能描述:RF 连接器 WEDGE CLAMP PANEL JACK RG188 RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型:
82-B1 制造商:3M Electronic Products Division 功能描述:80610981591 82-B1 WYE RESIN SP