- 您现在的位置：买卖IC网 > PDF目录378250 > 863532 (Sanyo Electric Co.,Ltd.) 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash PDF资料下载
参数资料
| 型号： | 863532 |
| 厂商： | Sanyo Electric Co.,Ltd. |
| 元件分类： | 8位微控制器 |
| 英文描述： | 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash |
| 中文描述： | 8位微控制器与2/4/8K字节在系统可编程闪存 |
| 文件页数： | 4/19页 |
| 文件大小： | 640K |
| 代理商： | 863532 |
LC863532A/28A/24A/20A/16A
No.6844-4/19
(13) Interrupts
- 12 sources 8 vectored interrupts
1. External Interrupt INT0
2. External Interrupt INT1
3. External Interrupt INT2, Timer/counter T0L (Lower 8 bits)
4. External Interrupt INT3, base timer
5. Timer/counter T0H (Upper 8 bits)
6. Timer T1H, Timer T1L
7. Vertical synchronous signal interrupt (VS), horizontal line (
HS
)
8. IIC
- Interrupt priority control
Three interrupt priorities are supported (low, high and highest) and multi-level nesting is possible. Low or high
priority can be assigned to the interrupts from 3 to 8 listed above. For the external interrupt INT0 and INT1, low or
highest priority can be set.
(14) Sub-routine stack level
- A maximum of 128 levels (stack is built in the internal RAM)
(15) Multiplication/division instruction
- 16 bits
×
8 bits (7 instruction cycle times)
- 16 bits / 8 bits (7 instruction cycle times)
(16) 3 oscillation circuits
- Built-in RC oscillation circuit used for the system clock
- Built-in VCO circuit used for the system clock and OSD
- X’tal oscillation circuit used for base timer, system clock and PLL reference
(17) Standby function
- HALT mode
The HALT mode is used to reduce the power dissipation. In this operation mode, the program execution is
stopped. This mode can be released by the interrupt request or the system reset.
- HOLD mode
The HOLD mode is used to stop the oscillations; RC (internal), VCO, and X’tal oscillations. This mode can be
released by the following conditions.
Pull the reset terminal (RES) to low level.
Feed the selected level to either P70/INT0 or P71/INT1.
(18) Package
- MFP36S
- DIP36S
(19) Development tools
- Flash EEPROM:
LC86F3548A
- Evaluation chip:
LC863096
- Emulator:
EVA86000 (main) + ECB863400 (evaluation chip board)
+ POD36-CABLE (cable)
+ POD36-DIP (for DIP36S)
or POD36-MFP (for MFP36S)
相关PDF资料 |
PDF描述 |
|---|---|
| 865GV | Intel 865G/865GV Graphics and Memory Controller Hub |
| 865G | Intel 865G/865GV Graphics and Memory Controller Hub |
| 8663 | T-1 Subminiature Lamps |
| 8664 | T-1 Subminiature Lamps |
| 8666 | T- Subminiature Lamps |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 863534-1 | 制造商:TE Connectivity 功能描述:CA LEAD 0.152M 16AWG 1 POS LGH SCKT - Bulk 制造商:TE Connectivity 功能描述:LGH LEAD SGL END POSITIVE STOP |
| 863534-2 | 制造商:TE Connectivity 功能描述:CA LEAD 0.203M 16AWG 1 POS LGH SCKT - Bulk 制造商:TE Connectivity 功能描述:LGH LEAD SGL END POSITIVE STOP |
| 863534-3 | 制造商:TE Connectivity 功能描述:CA LEAD 1.7526M 16AWG LGH - Bulk 制造商:TE Connectivity 功能描述:LGH-1/2L SGL MOLDED END LEAD |
| 863534-5 | 功能描述:电缆组件 LGH 1/2L SGL MLD END LEAD RoHS:否 制造商:Molex 产品:Power Assemblies 类型:Cable Assembly 连接器端口 A:No Connector 连接器端口 A 管脚计数:4 连接器端口 B:No Connector 连接器端口 B 管脚计数: 型式:Male 线规 - 美国线规（AWG）:20, 28 长度:0.305 m 颜色:Black, Red |
| 863534-6 | 制造商:TE Connectivity 功能描述:CA LEAD 0.457M 16AWG 1 POS LGH SCKT - Bulk 制造商:TE Connectivity 功能描述:LGH-1/2L SGL MOLDED END LEAD |
发布紧急采购，3分钟左右您将得到回复。